background image

Flight

Manual:

IMPORTANT: 

If the drone has difficulty standing still while in hover, it will need a GPS 

recalibration, refer to page 10 for the instructions

1) Follow all of the steps under the Pre-Flight section first
2) Refer to the FAA guidelines for safe and proper drone operation

To take off, bring the throttle stick up past 50%

To hover in place, leave the throttle at 50%

To descend, bring the throttle a little under 50%

To rotate the camera, twist the Aux 3 knob on the controller

GPS Mode

Position 0 (GPS): GPS is ON, Gyro active

Position 1 (Att.): GPS is OFF, Gyro active

Position 2 (FS): Failsafe (

For emergency use only!

)

NOTE: 

If you had to recalibrate the GPS as described on page 10, make sure

you followed step 12

Flight Mode Orientation 

Position 0: The default Flight Mode will make the drone move in relation to its 

own heading. Basically, its left will always be its left, forward is forward, back is 
back, etc.

Position 1: The Course Lock mode will save the current heading as the forward 

orientation whenever. So no matter how you rotate the drone in flight 

forward/back/left/right always remain the same. A new course can be set with a
flick of the switch during flight.

1

13

Page 12 

Summary of Contents for Onset


















Reviews: