background image

WARNINGS

Obey all federal, state, and local regulations

Do not fly in rain or other harsh conditions

Do not fly in wind more than 20mph

Do not fly faster than 10 m/s (22.5mph)

Operating in temperatures below 50° Fahrenheit (10° Celsius) will result in 

decreased flight times

Operating in temperatures below 32° Fahrenheit (0° Celsius) and below the 

mechanical and electrical components run the chance of seizing, resulting in 
drone malfunction and ultimately property damage, injury, and/or death

Always use the provided battery chargers

The drone will land in place when it reaches 10.5v

Keep away from spinning motors at ALL TIMES.

Do not attempt to modify the drone 

Do not attempt to repair the drone

NEVER allow minors to charge battery packs

NEVER drop power supply or batteries

NEVER attempt to charge damaged batteries

NEVER let batteries fully discharge unless you are disposing of them

NEVER attempt to charge a battery pack containing different types of batteries

NEVER charge a battery if the cable has been pinched or shorted

NEVER allow batteries to come into contact with moisture at any time

NEVER charge batteries in extremely hot or cold places or in direct sunlight

ALWAYS disconnect the battery after charging

ALWAYS end the charging process if the charger or battery becomes too hot

1

3

Page 2 

Summary of Contents for Onset


















Reviews: