background image

+1.866.977.7326 

www.preco.com 

3700076F 

Copyright 2016 

Page 6

 

 

Wireless Connect Screen (Mandatory) 
In  order  for  the  system  to  function,  the  display  must  be  told  what  wireless 
PreView

®

 sensor to communicate with.  To connect the display to the sensor, 

enter the Wireless Connect screen by pressing the 

 icon.  If the sensor is 

powered up and within range, it will show up on the screen like in the screen 
shot below: 

Wireless Connect Screen (Figure 1.6) 

 
 
 
 
 
 
 
 
 

 
Press  on  the  blue  box  containing  the  desired  sensor  serial  number to 
connect to that sensor.  After 2-3 seconds the display should connect to the 
sensor  and  the on  screen  message  will  change  to “Currently  married to 
sensor  XXXX”  (see Figure 1.7).   If  multiple  sensors  show  up,  choose the 
serial  number  that  corresponds  with the  last 4 digits of  the  sensor serial 
number on the same machine as the display. 
 

Critical: The sensor must be powered up in order for the display to see it!

 

 

Wireless Connect Screen 2 (Figure 1.7) 

 
 
 
 
 
 
 
 
 
 
 

 

 

 

Sensor Serial 

Number 

Summary of Contents for PreView WD7102

























Reviews: