background image

Precision Series / Energy Series Elliptical Fitness Crosstrainer Owner's Manual: EFX 425 / 423 / 225 / 222 / 221 

2

 

 

Never operate the unit if it is damaged, not 
working properly, when it has been dropped, or has 
been dropped in water. Return the equipment to a 
service center for examination and repair. 

DANGER 

The unit must be connected to a 
properly grounded circuit (refer to 

Grounding Instructions

). 

 

Keep the power cord and plug away from heated 
surfaces. 

 

Keep all electrical components, such as the power 
cord and power switch, away from liquids to 
prevent shock. 

 

Do not operate the equipment where aerosol 
(spray) products are being used or where oxygen 
is being administered. 

 

Do not use outdoors. 

 

Maintain the equipment in good working condition. 
Make sure that all fasteners are secure and the 
running belt is clean and running smoothly. 

 

Do not attempt to service the equipment yourself 
except to follow the maintenance instructions 
found in this manual. 

 

Never drop or insert objects into any opening. 
Keep hands away from moving parts. 

 

Use the equipment only for its intended purpose as 
described in this manual. Do not use accessory 
attachments that are not recommended by the 
manufacturer, as such attachments may cause 
injuries. 

 

Do not set anything on the handrails or hood. Place 
liquids, magazines, and books in the appropriate 
receptacles. 

 

Do not rock the unit. Do not lean or pull on the 
console at any time. 

 

Wear proper exercise clothing and shoes for your 
workout and avoid loose clothing. Do not wear 
shoes with heels or leather soles. Check the soles 
of your shoes and remove any dirt and embedded 
stones. Tie long hair back. 

 

Keep your body and head facing forward. Never 
attempt to turn around on the EFX. 

 

Do not overexert yourself or work to exhaustion. If 
you feel any pain or abnormal symptoms, stop 
your workout immediately and consult your 
physician. 

Summary of Contents for EFX 221












































































Reviews: