background image

©2019 Precor Inc. | Diverging Low Row RSL 324 | Assembly Guide

7

Route the Cable

Image

Hardware

Instructions

1

Tools: Hex wrench, 10 mm

Torque wrench

To connect cables to arms, remove the M12 x 45 mm SHCS, washers, and nuts on 

each side under arms. Place the cables end between the brackets and replace the 
fasteners. 

Tighten to 50 ft-lb (67.7 N-m).

2

Tools: Hex wrench, 8 mm
Hex wrench, 4 mm

To route the cable around the lower pulley on the weight stack tower, remove 

the cable retainer. Route the cable around the pulley and then replace the cable 
retainer.

3

Tools: Hex wrench, 8 mm

Open-end wrench, 19 mm

Torque wrench

T

o route the cable to the upper pulleys of weight stack tower, remove the cable 

retainers, route the cables, and replace the retainers.

 Tighten to 50 ft-lb (67 

N-m) of torque.

Seat Assembly

Image

Hardware

Instructions

1

2        M10 x 25 mm SHCS

2        washers, 11 mm

Tool: Hex wrench, 10 mm

Secure handlebars        to main frame       .

2

4        hex head screws 5/16-inch x 1½-inch

4        washers, 9 mm

Tool: Socket wrench, ½-inch with extension

Attach seat pad        to main frame       .

32

1

4

54

49

45

53

1

4

45

49

53

54

1

32

Summary of Contents for Resolute RSL 324













Reviews: