Prem-I-Air EH0533 Manual Download | Manualshive

Page: 15 / 15

background image

SERVICE WARRANTY

Prem-i-Air guarantees the product free from defects in materials
and workmanship for a period of twelve months.
Should this appliance be operated under conditions other than
those recommended, at voltages other than the voltage indicated
on the appliance, or any attempts made to service or modify the
appliance, then the warranty will be rendered void.
The product you buy may sometimes differ slightly from
illustrations. This warranty is in addition to, and does not affect,
your statutory rights.
If you have any problems with this product, please call our Help
Desk on (0845) 459 4816.

Prem-i-Air Appliances Ltd.,

Lancots Lane,

Sutton,

St. Helens,

Merseyside.

WA9 3EX

website: www.prem-i-air.com

Page 15

«
...
13
14
15

Summary of Contents for EH0533
















Reviews:

No comments

Related manuals for EH0533

Brand: FAAC Pages: 14

Brand: E-fly Pages: 16

Brand: Hardi Pages: 2

Brand: YASKAWA Pages: 64

Brand: V2 Pages: 3

Brand: Panasonic Pages: 27

Brand: Panasonic Pages: 78

Brand: Panasonic Pages: 98

Brand: NAiS Pages: 173

Brand: Panasonic Pages: 2

Brand: Samson Pages: 52

Brand: WAGNER Pages: 60

UTAdvanced UT35A

Brand: YOKOGAWA Pages: 18

Brand: Eaton Pages: 8

Brand: ABB Pages: 44

Brand: Omega Pages: 2

Brand: Zmotion Pages: 34

Brand: Burkert Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands