background image

COMPLETION ITEMS

Potenza 10 1400 Kv Brushless 

Outrunner Motor 

(FPZM1010C)

ZTW 50A ESC with 5V/8A BEC 

(ZTW50ABEC)

Potenza DS15 Digital Servos 

(FPZDS15)

Aura 8 Advanced Flight Control 

System

 (FPZAURA08ZZE300G2)

11.5 x 4.5 Electric SR Propeller 

(FPMP1145E)

2100-3300mAh 3S 11.1V 35C+ Li-Po

(FPZB22003S45)

6+ Channel Computer Transmitter

NEEDED TO 

COMPLETE

INST

ALLED!

INST

ALLED!

SPECIFICATIONS

47.8 in. (1215mm)

47.8 in. (121

5m

m

)

Standard: 3lb 1oz. (1390g)

RTF with 3S 2200mAh ba

ery installed

572.5 sq. in.

(40 sq. dm.)

BATTERY CHARGING GUIDELINES

The assembly of the QQ Extra 300G2 can be accomplished in 

less than one hour. Prior to assembling the airplane, it is 

advisable to charge your battery so that you are ready to begin 

setup upon completion of the assembly of your model.

We recommend the use of an advanced Li-Po balancing 

charger for your batteries to get the maximum performance 

and lifespan.

Our airplanes are designed around our Potenza Li-Po 

batteries, and we recommend the Potenza 3S 2200mAh 45C 

Li-Po based on our extensive testing and development. These 

batteries feature an EC3 connector, so no soldering is required 

for use in your QQ Extra 300G2.

All are available at www.flexinnovations.com 

WARNING

FOLLOW ALL INSTRUCTIONS PROVIDED BY YOUR 

BATTERY AND CHARGER MANUFACTURER. 

FAILURE TO COMPLY CAN RESULT IN FIRE.

OPTIONAL ACCESSORIES

Receiver

INST

ALLED!

INST

ALLED!

INCLUDE

D!

NEEDED TO 

COMPLETE

NEEDED TO 

COMPLETE

Spektrum DSMX Remote Receiver(s)
Spektrum SRXL
Futaba S.Bus
Hitec S.Bus
Graupner SumD,
JR XBus Mode B
Jeti UDI 12 
6+ Channel Receiver (any brand)

REPLACEMENT PARTS

3

FPM307001
FPM378001
FPM307002
FPM378002
FPM307003
FPM307004
FPM307005
FPM307006
FPM307007
FPM37708
FPM37709
FPM307010
FPMA0003
FPMP11545E
FPZM1010C
FPZM1010A1
FPZM1010A2
FPZM1010A3
FPZA1016
ZTW50ABEC
FPZAURA08ZZE300G2
FPZAU02

Fuselage (Day)
Fuselage (Night)
Wing Set (Day) with SFGs
Wing Set (Night) with SFGs
Tail Set with Rudder
Cowling and Hatch Set
Landing Gear with Wheels & Wheel Pants
Wing and Stab Tube Joiner Set
Pushrod Set
Red/Black Decal Set
Green/Black Decal Set
Spinner
Plastic Clevis Set (10)
SR 11.5 x 4.5E Propeller
Potenza 10 1400kv Motor (3S)
5mm Collet Prop Adapter
Potenza 10 Aluminum X-Mount with Screws
Potenza 10 5mm Motor Shaft with Collar
Potenza Advanced LED Controller
ZTW 50A ESC 3S/6S with 8A BEC
Potenza Aura 8 AFCS for QQ 300G2
Aura Micro-USB to USB Cable

FPZAU01
FPZB22003S45
FPZB26003S45
FPZM1010D
FPMPAPC1245MR
FPZB22004S40
FPZB26004S45
FPZA1010
ZTWCARD
SPMAR8010T
SPM9745
FUTR2001SB
FUTR7003SB
FUTT6K

Potenza 3pc. Male-Male Servo Connectors
Potenza 3S 2200mAh 45C Li-Po
Potenza 3S 2600mAh 45C Li-Po
Potenza 10 1070kv Motor (for 4S batteries)
APC 12x4.5 MR Propeller (for 4S)
Potenza 4S 2200mAh 40C Li-Po
Potenza 4S 2600mAh 45C Li-Po
Potenza Digital Battery Analyzer
ZTW ESC Programming Card
Spektrum AR8010T DSMX Receiver
Spektrum DSMX Remote Receiver
R2001SB S.BUS S-FHSS Receiver
R7003SB S.BUS FASSTest Receiver
Futaba T6K Transmitter w/R3006SB Reeiver

(Recomended

SPM Receiver)

(Recomended

FUT Receiver)

Summary of Contents for QQ EXTRA 300G2






























Reviews: