background image

 

Page | 17 

 

 

Embest Technology takes no responsibility for fulfilling any warranty 

(verbal or written) that is not made by Embest Technology and not 

included in the scope of our warranty. 

3.

 

Within the period of warranty, the cost for sending products to 

Embest should be paid by the customer. The cost for returning 
the  product  to  the  customer  will  be  paid  by  Embest.  Any 
returns in either direction occurring after the warranty period 
has expired should be paid for by the customer. 

4.

 

Please contact technical support with any repair requests. 

 

Note:   

 

Embest  Technology  will  not  take  any  responsibility  for  products  returned 
without the prior permission of the company. 

2.3

 

Basic guidelines for protection and 

maintenance of LCDs 

1.

 

Do not use finger nails or other hard sharp objects to touch the 

surface of the LCD 

2.

 

Embest recommends purchasing specialist wipes to clean the 

LCD  after  long  time  use,  avoid  cleaning  the  surface  with 
fingers or hands as this may leave fingerprints or smudges. 

3.

 

Do  not  clean  the  surface  of  the  screen  with  unsuitable 

chemicals 

 

Note:   

 

Embest  do  not  supply  a  maintenance  service  for  LCDs.  We  suggest  the 
customer immediately checks the LCD once in receipt of the goods. In the 
event that the LCD does not run or shows no display, the customer should 
inform Embest within 7 business days of delivery. 

Summary of Contents for Embest SBC8140






















Reviews: