background image

 

Warning Sign 

Warning Sign Must Be Posted

 – The red 

WARNING sign like the one shown is packed 
with your new hot tub.  This sign must be posted 
in a prominent place in close proximity to the hot 
tub installation site immediately upon completion 
of hot tub installation. 

 

Important:  It is extremely important that this sign be permanently placed in clear 
view of persons using the hot tub.  Occasional hot tub users may not be aware of 
some of the dangers hot water poses to pregnant women, small children, 
seniors, and people under the influence of alcohol.  If you did not receive a 
warning sign or your sign has become damaged, please call your local dealer for 
a replacement. 

Hyperthermia 

To reduce the risk of injury, the water temperature in a hot tub should never 
exceed 104˚F (40˚C).  Water temperatures between 100˚F (38˚C) and 104˚F 
(40˚C) are considered safe for a healthy adult.  Lower water temperatures are 
recommended for young children, senior citizens, persons with sensitivities, and 
when hot tub use exceeds 10 minutes. 

WATER TEMPERATURE IN EXCESS OF 100˚F (38˚C) MAY BE INJURIOUS 
TO YOUR HEALTH. 

Hyperthermia occurs when the internal temperature of the body reaches a level 
several degrees above the normal body temperature of 98.6˚F (37˚C).  The 
symptoms of hyperthermia include drowsiness, lethargy, and an increase in the 
internal temperature of the body.  The effects of hyperthermia include: 

  Unawareness of impending hazard 
  Failure to perceive heat 
  Failure to recognize the need to exit hot tub 
  Physical inability to exit hot tub 
  Fetal damage in pregnant women 
  Unconsciousness and danger of drowning 

If you sense any of the symptoms of hyperthermia, safely exit the hot tub 
immediately. 

 

SAVE THESE INSTRUCTIONS 

 

 

 

Page 5 

For HELP, call 727.573.9611

 

Summary of Contents for Sterling Leisure













































































Reviews: