24
Error messages from the N
2
Control
The following table shows which error message can be generated by the N2 Control.
No.
Error message display row 1
Error message display row 2
Description
Source message
120
No ECD display message
Start of device specific error
ERR_N2DEVICEBASE
121
CAN-bus extension
not available
Communication with CAN-extension print fault
ERR_N2EXTENSION_NA
122
No ECD display message
N2Control is in manual mode
ERR_N2MANUALMODE
123
No ECD display message
Reserved error
ERR_N2RESERVED_123
124
CAN-bus 3
bus fault
CAN-bus 3 bus fault
ERR_N2CAN3_BUSERROR
125
CAN-bus 4
bus fault
CAN-bus 4 bus fault
ERR_N2CAN4_BUSERROR
126
No ECD display message
Reserved error
ERR_N2RESERVED_126
127
No ECD display message
Reserved error
ERR_N2RESERVED_127
128
No ECD display message
Reserved error
ERR_N2RESERVED_128
129
No ECD display message
Reserved error
ERR_N2RESERVED_129
130
N2 master detects
a compressor error
There is a compressor within the system with a fault
ERR_N2COMPRESSOR_ERROR
131
Compressor
not ready
The compressor of this N2Control is not ready
ERR_N2COMPRESSOR_NOTREADY
132
Compressor
fault input active
The compressor of this N2Control has a fault (according
to fault input)
ERR_N2COMPRESSOR_FAULTINPUT
133
Compressor
not available
There is no compressor available within the system
ERR_N2COMPRESSOR_NONEAVAILABLE
134
Compressor
active timeout
The compressor has not become active
ERR_N2COMPRESSOR_ACTIVETIMEOUT
135
Compressor
producing timeout
The compressor is not producing
ERR_N2COMPRESSOR_PRODUCINGTIMEOUT
136
Compressor
unload timeout
The compressor runs to long in idle (no load)
ERR_N2COMPRESSOR_UNLOADTIMEOUT
137
Compressor
disabled
The compressor is disabled
ERR_N2COMPRESSOR_DISABLED
138
No ECD display message
Reserved error
ERR_N2RESERVED_138
139
No ECD display message
Reserved error
ERR_N2RESERVED_139
140
N2 master detects
a Psa error
There is a PSA generator within the system with a fault
ERR_N2PSAGENERATOR_ERROR
141
Psa generator
no sync received
PSA generator has missed to many synchronization
messages
ERR_N2PSAGENERATOR_NOSYNCRECEIVED
142
Psa generator
dryer fault
PSA generator dryer fault
ERR_N2PSAGENERATOR_DRYERFAULT
143
Psa generator
compressorpressure
PSA generator compressor pressurevalve fault
ERR_N2PSAGENERATOR_COMPAIRPRESSURESWITCH
144
Psa generator
beko(moisture) fault
PSA generator bekoguard fault
ERR_N2PSAGENERATOR_BEKOGUARDSENSOR
145
Psa generator
Dust filter fault
PSA generator dustfilter fault
ERR_N2PSAGENERATOR_DUSTFILTERSENSOR
146
Psa generator
Dewpoint sensor
PSA generator dew point sensor fault
ERR_N2PSAGENERATOR_DEWPOINTSENSOR
147
Psa valve set 1
settings
Settings of the master do not match with PSA 1
ERR_N2PSAVALVE_SETTINGS01
148
Psa valve set 2
settings
Settings of the master do not match with PSA 2
ERR_N2PSAVALVE_SETTINGS02
149
Psa valve set 3
settings
Settings of the master do not match with PSA 3
ERR_N2PSAVALVE_SETTINGS03
150
Air flow in
Sensor error
Flow in sensor is not found
ERR_N2AIRFLOWIN_NOSENSOR
151
Air flow in
minimal
Flow in is set lower than value at this production
ERR_N2AIRFLOWIN_MIN
152
Air flow in
maximal
Flow in is set higher than value at this production
ERR_N2AIRFLOWIN_MAX
153
N2 flow out
Sensor error
Flow out sensor is not found
ERR_N2N2FLOWOUT_NOSENSOR
154
N2 flow out
minimal
Flow out is set lower than value at this production
ERR_N2N2FLOWOUT_MIN
Summary of Contents for LOX
Page 2: ...2 ...
Page 8: ...8 Figure 1 Schematic setup of the LOX system basics ...
Page 45: ......
Page 46: ......
