10
levage, des câbles de grue ou divers chemins élec-
triques.
g. Empêchez l’apparition de toute humidité, notamment sur
vos vêtements, à la surface de l’emplacement de travail, des
câbles, du porte-électrode et du poste de soudage/coup-
age. Réparez immédiatement toute fuite d’eau.
4. VENTILATION-- La respiration prolongée des fumées résul-
tant des opérations de soudage/coupage, à l’intérieur, d’un
local clos, peut provoquer des malaises et des dommages
corporels. Aussi convient-il d’observer les précautions
suivantes:
a. Assurez en permanence une aération adéquate de
l’emplacement de travail en maintenant une ventilation
naturelle ou à l’aide de moyens mécaniques. N’effectuez
jamais de travaux de soudage ou de coupage sur des ma-
tériaux de zinc, de plomb, de beryllium ou de cadmium en
l’absence de moyens mécaniques de ventilation capables
d’empêcher l’inhalation des fumées dégagées par ces
matériaux.
b. N’effectuez jamais de travaux de soudage ou de coupage
à proximité de vapeurs d’hydrocarbure chloré résultant
d’opérations voisines de dégraissage ou de pulvérisa-
tion. La chaleur dégagée ou le rayonnement de l’arc peut
déclencher la formation de phosgène -- gaz particulière-
ment toxique -- et d’autres gaz irritants, à partir des vapeurs
de solvant.
c. Une irritation momentanée des yeux, du nez ou de la gorge
constatée au cours de l’utilisation de l’équipement dénote
un défaut de ventilation. Arrêtez-vous de travailler afin de
prendre les mesures néces-
saires à l’amélioration de
la ventilation. Ne poursuivez pas l’opération entreprise si
le malaise persiste.
d. Certaines commandes comportent des canalisations
où circule de l’hydrogène. L’armoire de commande est
munie d’un ventilateur destiné à empêcher la forma-
tion de poches d’hydrogène, lesquelles présentent un
danger d’explosion; ce ventilateur ne fonctionne que si
l’interrupteur correspondant du panneau avant se trouve
placé en position ON (Marche). Veillez à manœuvrer cette
commande en vérifiant si le couvercle est bien en place,
de façon à assurer l’efficacité de la ventilation ainsi réalisée.
Ne jamais débrancher le ventilateur.
e. Les fumées produites par l’opération de soudage ou de
coupage peuvent s’avérer toxiques. Aussi est-il nécessaire
de disposer en permanence d’un dispositif adéquat de
ventilation de type aspirant, afin d’élimi-ner du voisinage
de l’opérateur tout dégagement de fumée visible.
f. Consultez les recommandations particulières en matière
de ventilation indiquées à l’alinéa 6 de la norme Z49.1
de l’AWS.
5. ENTRETIEN DE L’éQUIPEMENT-- Un équipement entretenu
de façon défectueuse ou inadéquate risque non seulement
de réaliser un travail de mauvaise qualité mais, chose plus
grave encore, d’entraîner des dommages corporels graves,
voire mortels en déclenchant des incendies ou des chocs
électriques. Observez par conséquent les précautions
suivantes:
a. Efforcez-vous de toujours confier à un personnel qua-lifié
l’installation, le dépannage et l’entretien du poste de soud-
age et de coupage. N’effectuez aucune réparation électrique
sur l’équipement à moins d’être qua-lifié à cet effet.
b. Ne procédez jamais à une tâche d’entretien quelconque
à l’intérieur du poste de soudage/coupage, avant d’avoir
débranché l’alimentation électrique.
c. Maintenez en bon état de fonctionnement les câbles, le
câble de masse, les branchements, le cordon d’alimentation
et le poste de soudage/coupage. N’utilisez jamais le poste ou
l’équipement s’il présente une défectuosité quelconque.
d. Prenez soin du poste de soudage et de coupage et des
équipements accessoires. Gardez-les à l’écart des sources de
charleur, notamment des fours, de l’humidité, des flaques
d’eau maintenez-les à l’abri des traces d’huile ou de graisse,
des atmosphères corrosives et des intempéries.
e. Laissez en place tous les dispositifs de sécurité et tous les
panneaux de l’armoire de commande en veillant à les
garder en bon état.
f. Utilisez le poste de soudage/coupage conformément à son
usage prévu et n’effectuez aucune modification.
6. INFORMATIONS COMPLéMENTAIRES RELATIVES à LA Sé-
CURITé--
Pour obtenir des informations complémentaires sur les
règles de sécurité à observer pour le montage et l’utilisation
d’équipements de soudage et de coupage électriques et
sur les méthodes de travail recommandées, demandez
un exemplaire du livret N° 52529 “Precautions and Safe
Practices for Arc Welding, Cutting and Gouging” publié
par Prest-O-Lite. Nous conseillons également de consulter
les publications sui-vantes, tenues à votre disposition par
l’American Welding Society, 550 N.W. LeJuene Road, Miami,
FL 32126:
a. “Safety in Welding and Cutting” AWS Z49.1
b. “Recommended Safe Practices for Gas-Shielded Arc Welding
“AWS A6. 1.
c. “Safe Practices for Welding and Cutting Containers That Have
Held Combustibles” AWS-A6.0.
d. “Recommended Safe Practices for Plasma Arc Cutting”
AWS-A6. 3.
e. “Recommended Safe Practices for Plasma Arc Welding”
AWS-C5. 1.
f. “Recommended Safe Practices for Air Carbon Arc Gouging
and Cutting” AWS-C5. 3.
g. “Code For Safety in Welding and Cutting” CSA-Standard
W117. 2.
PRéCAUTIONS De SéCURITé
Summary of Contents for 380
