background image

 

12 

Lighting Instructions 

 

 

Caution: 

Never operate the grill unattended. Do not operate the rotisserie or Sear Zone burner with the 

hood closed. 

 

Prior to using your grill, make sure all of the following is correctly completed: 

 

Verify that the burner tube is free of insects and insect nests, webs, etc. 

 

Verify installation of the proper gas type and regulator settings. 

 

Verify that the proper gas connection is complete. 

 

Minimum clearances are maintained. 

 

All packaging has been removed. 

 

All parts and components are properly in place. 

 

That an installer supplied manual gas shut-off valve is fully accessible. 

 

Clean and inspect LP hose for cuts, wear, abrasion, or leaks. Replace if necessary with a suitable         

UL, ETL or CSA Listed part with internally threaded connector. 

 

LIGHTING YOUR GRILL 

 

Become  familiar  with  the  safety  instructions  at  the  front  of  this  manual.  Do  not  smoke  while 
lighting the grill or checking the gas supply connections. 

 

Make sure that all gas connections are securely tightened and have been leak tested with a soapy 
water solution - never with a flame! 

 

READ THESE GRILL AND ROTISSERIE LIGHTING INSTRUCTIONS BEFORE LIGHTING 

-  KEEP  THE  GRILL  HOOD  OPEN  DURING  THE  LIGHTING  PROCESS.    MAKE  SURE  ALL  THE 
BURNER KNOBS ARE TURNED TO THE "OFF" POSITION. 
- PUSH IN AND TURN THE KNOB TO THE HIGHEST POSITION SETTING. 
-PRESS THE IGNITION BUTTON IN AND HOLD UNIIL THE GRILL BURNER IGNITES. 
- IF THE BURNER DOES NOT IGNITE WITHIN 5 SECONDS, TURN THE BURNER TO THE "OFF" 
POSITION AND WAIT 5 MINUTES.    REPEAT THE ABOVE STEPS. 

 
TO SAFELY SHUT DOWN THE GRILL, TURN ALL BURNERS TO THE "OFF" POSITION.    FOR LP 
GAS MODELS, IN ADDITION IO TURNING THE BURNERS OFF, TURN THE VALVE ON THE GAS 
CYLINDER TO THE "OFF" POSITION WHEN NOT IN USE. 

 

 

If the burner still does not light, refer to the manual and make sure the unit is set up properly before 
calling for service. 

 

 

Warranty work in not provided for customer education on the operation of the unit. 

 

TROUBLESHOOTING: 

 

Make  sure  the  battery  is  operational.  The  grill  ignition  system  uses  9  Volt  batteries  and  prolonged 
exposure to heat when not is use will disable the battery. Batteries are not covered under any warranty. 

 

If your grill fails to properly light, wait five minutes and repeat the above procedures. 

Summary of Contents for GBQC36




















Reviews: