PREVOST LE MIRAGE XLII BUS SHELLS Maintenance Manual Download

Page: 452 / 1260

m a i n

local

global

o p e r a t i o n

Using light oil, lubricate the treadle roller, roller pin, and hinge

pin.

Check the rubber plunger boot for cracks, holes or deterio-

ration and replace if necessary. Also, check mounting plate

and treadle for integrity.

Apply 2 to 4 drops of oil between plunger and mounting

plate -

do not over oil!

Every year, or 100,000 miles, or 3,600 operating hours:

Disassemble, clean parts with mineral spirits, replace all

rubber parts, or any part worn or damaged. Check for proper

operation before placing vehicle in service.

SERVICE CHECKS

OPERATING CHECK

Check the delivery pressure of both primary and secondary

circuits using accurate test gauges. Depress the treadle to

several positions between the fully released and fully ap-

plied positions, and check the delivered pressure on the

test gauges to see that it varies equally and proportionately

with the movement of the brake pedal.

After a full application is released, the reading on the test

gauges should fall off to zero promptly. It should be noted

that the primary circuit delivery pressure will be about 2 PSI

greater than the secondary circuit delivery pressure with

both supply reservoirs at the same pressure. This is normal

for this valve.

Important:

A change in vehicle braking characteristics or a

low pressure warning may indicate a malfunction in one or

the other brake circuit, and although the vehicle air brake

system may continue to function, the vehicle should not be

operated until the necessary repairs have been made and

both braking circuits, including the pneumatic and mechani-

cal devices, are operating normally. Always check the vehicle

brake system for proper operation after performing brake

work and before returning the vehicle to service.

LEAKAGE CHECK

1. Make and hold a high pressure (80 psi) application.
2. Coat the exhaust port and body of the brake valve with a

soap solution.

3. Leakage permitted is a one inch bubble in 3 seconds. If

the brake valve does not function as described above or

leakage is excessive, it is recommended that it be re-

placed with a new or remanufactured unit, or repaired

with genuine Bendix parts available at authorized Ben-

dix parts outlets.

Refer to figures 4, 5 and 6 for item numbers referenced in

parenthesis.

REMOVAL

1. Chock the vehicle wheels or park the vehicle by

mechanical means. (Block and hold vehicle by means

other than air brakes.) Drain all air system reservoirs.

2. Identify and disconnect all supply and delivery lines at

the brake valve.

3. Remove the brake valve and treadle assembly from the

vehicle by removing the three cap screws on the outer

bolt circle of the mounting plate. The basic brake valve

alone can be removed by removing the three cap screws

on the inner bolt circle.

DISASSEMBLY

(Figures 4, 5 and 6)

1. If the entire brake valve and treadle assembly was re-

moved from the vehicle, remove the three cap screws

securing the treadle assembly to the basic brake valve.

2. Remove the screw (9) securing the exhaust diaphragm

(10) and washer (11) to the exhaust cover (12).

3. Remove the four screws that secure the exhaust cover

(12) to the lower body.

4. Remove the secondary inlet and exhaust valve assem-

bly (13) from the lower body.

5. Remove the four hex head cap screws securing the lower

body to the upper body and separate the body halves.

6. Remove the rubber seal ring (14) from the lower body.
7.

For E-8P only:

While applying thumb pressure to the

primary piston (22), lift out and up on the three lock tabs

of the primary piston retainer (15).

For E-10P only:

While depressing spring seat (7), re-

move retaining ring (8). Remove spring seat (7) and coil

spring (5).

Caution:

Before proceeding with the disassembly, re-

fer to Figures 3 and 4 and note that the lock nut (16)

and stem (17) are used to contain the primary pis-

ton return spring (

for E-8P:

23,

for E-10P:

6), stem

spring (19), and the relay piston spring (21). The com-

bined force of these springs is approximately 50

pounds and care must be taken when removing the

lock nut as the spring forces will be released. It is

recommended that the primary piston and relay pis-

ton be manually or mechanically contained while the

nut and stem are being removed.

9. Using a 3/8” wrench, hold the lock nut (16) on the threaded

end of the stem (17). Insert a screwdriver to restrain the

stem, remove the lock nut (16), spring seat, (18) and

stem spring (19).

10.

For E-10P only:

Remove adapter (1) and o-ring (4).

Remove the primary piston (2) from adapter (1) and o-

ring (34) from the primary piston (2).

Summary of Contents for LE MIRAGE XLII BUS SHELLS












































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for LE MIRAGE XLII BUS SHELLS

Reviews:

Related manuals for LE MIRAGE XLII BUS SHELLS

Brands by name

Popular brands

PREVOST LE MIRAGE XLII BUS SHELLS, Maintenance Manual

Search results

Summary of Contents for LE MIRAGE XLII BUS SHELLS

Reviews:

Related manuals for LE MIRAGE XLII BUS SHELLS

Brands by name

Popular brands