manualshive.com logo in svg

PREVOST LE MIRAGE XLII, Maintenance Manual

The PREVOST LE MIRAGE XLII maintenance manual is an essential resource for owners and operators. This comprehensive manual covers all aspects of maintenance, providing detailed instructions and guidelines. Download this invaluable manual for free from 88.208.23.73:8080, ensuring you have the necessary knowledge and support to optimize the performance of your PREVOST LE MIRAGE XLII.

Share
Download
background image

Section 22: HEATING AND AIR CONDITIONING 

 

PA1553 

14 

5.  The success of the air conditioning system 

depends on retaining the conditioned air 
within the vehicle. All windows and intake 
vents should be closed. An opening of 
approximately 8 in

2

 (5162 mm

2

) could easily 

neutralize the total capacity of the system. 

6.  Other causes of inadequate cooling are 

dirty coils or filter. Dirt acts as insulation and 
is also serves as a restriction to the air flow. 

7.  The refrigeration load is not constant and 

varies. It is also affected by outside 
temperature, relative humidity, passenger 
load, compressor speed, the number of 
stops, etc.  

8. The compressor will load or unload 

depending on operating conditions. 

8.2 REFRIGERANT 

The A/C system of this vehicle has been 
designed to use Refrigerant 134a as a medium. 
Regardless of the brand, only R-134a must be 
used in this system. The chemical name for this 
refrigerant is Ethane, 1, 1, 1, 2-Tetrafluoro. 

 

DANGER

 

Refrigerant in itself is nonflammable, but if it 
comes in contact with an open flame, it will 
decompose. 

8.2.1 Procurement 

Refrigerant is shipped and stored in metal 
cylinders. It is serviced in 30 and 100 pound 
(13,6 and 45 kg) cylinders. Approximately 24 
pounds (10,9 kg) are used in the system. 
It will be impossible to draw the entire refrigerant 
out of the cylinder. However, the use of warm 
water when charging the system will assure the 
extraction of a maximum amount of refrigerant 
from the cylinder. 

8.2.2  Precautions in Handling Refrigerant 

1.  Do not leave refrigerant cylinder uncapped. 

2.  Do not subject cylinder to high temperatures, 

do not weld or steam clean near system or 
cylinder. 

3.  Do not fill cylinder completely.  

4.  Do not discharge vapor into an area where 

a flame is exposed. 

5.  Do not expose the eyes to liquid refrigerant. 

WARNING

 

One of the most important precautions when 
handling refrigerant consists in protecting the 
eyes. Any liquid refrigerant which may 
accidentally escape is approximately -40

o

F (-

40

o

C). If refrigerant comes in contact with the 

eyes, serious injury could result. Always wear 
goggles to protect the eyes when opening 
refrigerant connections. 

All refrigerant cylinders are shipped with a heavy 
metal screw cap. The purpose of the cap is to 
protect the valve and safety plug from damage. 
It is a good practice to replace the cap after 
each use of the cylinder for the same reason. If 
the cylinder is exposed to the sun’s radiant heat 
pressure increase resulting may cause release 
of the safety plug or the cylinder may burst. 

For the same reason, the refrigerant cylinder 
should never be subjected to excessive 
temperature when charging a system. The 
refrigerant cylinder should be heated for 
charging purposes by placing it in 125

o

F (52

o

C) 

water. Never heat above 125

o

F (52

o

C) or use a 

blowtorch, radiator, or stove to heat the cylinder. 
Welding or steam cleaning on or near any 
refrigerant line or components of the A/C system 
could build up dangerous and damaging 
pressures in the system. 

If a small cylinder is ever filled from a large one, 
never fill the cylinder completely. Space should 
always be allowed above the liquid for 
expansion. Weighing cylinders before and 
during the transfer will determine the fullness of 
the cylinders. 

8.2.3  Treatment in Case of Injury 

If liquid refrigerant comes in contact with the 
skin, treat the injury as if the skin was frost-bitten 
or frozen. If liquid refrigerant comes in contact 
with the eyes, consult an eye specialist or doctor 
immediately. Give the following first aid 
treatment: 

1.  Do not rub the eyes. Splash eyes with cold 

water to gradually bring the temperature 
above the freezing point. 

2.  Apply drops of sterile mineral oil (obtainable 

at any drugstore) in the eyes to reduce the 

Summary of Contents for LE MIRAGE XLII































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for LE MIRAGE XLII

Brands by name

Popular brands

Load more brands