manualshive.com logo in svg

PREVOST LE MIRAGE XLII, Maintenance Manual

The PREVOST LE MIRAGE XLII maintenance manual is an essential resource for owners and operators. This comprehensive manual covers all aspects of maintenance, providing detailed instructions and guidelines. Download this invaluable manual for free from 88.208.23.73:8080, ensuring you have the necessary knowledge and support to optimize the performance of your PREVOST LE MIRAGE XLII.

Share
Download
background image

Section 06: ELECTRICAL 

 

PA1553 

22 

enough to prevent the batteries from moving, but 
they should not be tightened to the point that 
excessive strain is placed on the battery 
hold-down cover (proper tightening torque: 45-55 
lbf-in (5-6 Nm). 

To insure good contact, the battery cable ring 
terminals should be tight on the battery posts. If 
the posts or cable ring terminals are corroded, 
the cables should be disconnected and the posts 
and clamps cleaned separately with a soda 
solution and a wire brush. Install cable ring 
terminals on battery posts and tighten to a torque 
of 10-15 lbf-ft (13-20 Nm). Replace protective 
caps to prevent corrosion and sparks. 

3.8 COMMON CAUSES OF BATTERY 

FAILURE 

When a battery fails, the cause of failure may be 
related to something other than the battery. For 
this reason, when a battery failure occurs, do not 
be satisfied with merely recharging or replacing 
the battery. Locate and correct the cause of the 
failure to prevent recurrence. Some common 
external causes of battery failure are as follows: 

1.  A defect in charging system such as high 

resistance or a faulty alternator or regulator. 

2.  A malfunction within the 12 volts system 

(equalizer). 

3.  Overloads caused by a defective starter or 

excessive use of accessories. 

4.  Dirt and electrolyte on top of the batteries 

causing a constant drain. 

5.  Hardened battery plates, due to battery 

being in a low state of charge over a long 
period of time. 

6.  Shorted cells, loss of active material from 

plates. 

7.  Driving conditions or requirements under 

which the vehicle is driven for short periods 
of time. 

8.  A constant drain caused by a shorted circuit 

such as an exposed wire or water infiltration 
in junction boxes causing ground fault. 

9.  Extended operation of preheating system 

with engine not running. 

10. Failing to close disconnect switches during 

the night. 

3.9 TROUBLESHOOTING 
If a battery is known to be good and then has not 
performed satisfactorily in service for no 
apparent reason, the following factors may 
reveal the cause of trouble: 

1.  Vehicle accessories and disconnect switches 

inadvertently left on overnight. 

2.  Defects in the charging system, such as high 

wiring resistance, faulty alternator, regulator 
or battery equalizer. 

3. A vehicle electrical load exceeding the 

alternator (or battery equalizer) capacity, with 
the addition of electrical devices, such as CB 
radio equipment, a cellular phone or 
additional lighting systems. 

4.  Defects in the electrical system, such as 

shorted or pinched wires. 

5.  Extended driving at a slow speed while using 

many accessories. 

6. Loose or poor battery cable-to-post 

connections, previous improper charging of a 
run-down battery, or loose hold-down clamp 
bolts. 

7.  High-resistance connections or defects in the 

cranking system. 

 

3.10  "BAT" BATTERY VOLTAGE INCORRECT 

TELLTALE LIGHT 

If the 

“

BAT

" 

(battery voltage incorrect) telltale 

light is illuminated, check the 24-volt voltmeter to 
determine if the battery voltage is too high or too 
low. 
 

NOTE 

According to the battery charging condition, it 
is normal that "BAT" telltale light illuminates 
upon starting the engine and stays illuminated 
for a few seconds. This is caused by the 
normal voltage drop of the battery during 
starting.

 

3.10.1  "Bat" Telltale Light Definitions 

Voltmeter drops below 24.4 volts dc 

o

  Check alternator output. 

o

  Check voltage regulator. 

o

  Check battery connections. 

o

  Check battery cells. 

Summary of Contents for LE MIRAGE XLII































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for LE MIRAGE XLII

Yutong LJ17LLJ User Manual preview
LJ17LLJ
Brand: Yutong Pages: 7

Brands by name

Popular brands

Load more brands