manualshive.com logo in svg

PREVOST LE MIRAGE XLII, Maintenance Manual

The PREVOST LE MIRAGE XLII maintenance manual is an essential resource for owners and operators. This comprehensive manual covers all aspects of maintenance, providing detailed instructions and guidelines. Download this invaluable manual for free from 88.208.23.73:8080, ensuring you have the necessary knowledge and support to optimize the performance of your PREVOST LE MIRAGE XLII.

Share
Download
background image

Section 12: BRAKE AND AIR SYSTEM 

 

PA1553 

7

Change cartridge every 100,000 miles (160 000 
km) or once every two years, whichever comes 
first. The air dryer may be purged for mainte-
nance purposes using the remote drain valve 
located in the engine compartment and 
accessible through the engine compartment 
R.H. side door. The valve is positioned over the 
battery assembly, close to the door hinge or 
close to the L.H. side of door opening depending 
on type of vehicle (Fig. 2). The air filter/dryer has 
a built-in governor to maintain the system 
between 108 psig and 123 psig. 

Maintenance and repair information is supplied 
in the maintenance information annexed to this 
section. 

7.1 

AIR FILTER/DRYER PURGE TANK 

A tank is supplied to purge the air filter/dryer to 
remove moisture and contaminants. 

8. AIR 

LINES 

Copper piping, nylon-reinforced tubing, and 
flexible hoses are used to connect the units in 
the pneumatic system, including air brake 
system, suspension system and accessory 
systems such as the entrance door, fresh air 
damper cylinder, air horns, etc. Furthermore, the 
nylon tubing is color coded to ease identification. 
Refer to the following table for the complete 
color identification code. Service instructions for 
each type of air line are also provided under the 
applicable headings. 

Color 

Circuit 

Red Secondary 

Green 

Primary and Delivery 

Yellow Parking 

Brake 

Blue Suspension 

Black Accessory 

Brown Trailer 

Brake 

8.1 COPPER 

PIPING 

A heat dissipation copper piping assembly is 
used to dissipate the heat coming from the 
compressor before it enters the air filter/dryer. 
Connections should be checked for leakage at 
least every 6,250 miles (10 000 km) or twice a 
year, whichever comes first. Tighten or replace 
when necessary. When replacing copper piping, 
the parts must be free of burrs, copper cuttings, 
and dirt. Blow out piping with compressed air. 
Any such particles will destroy sealing seats in 
air control units. Also, new piping must be the 
same size as the old one. 

8.2 FLEXIBLE 

HOSES 

A flexible hose is used normally where it is 
impractical to use copper or nylon tubing due to 
constant flexing during operation, such as brake 
chamber hoses. Hose connections should be 
tested for leakage at least every 6,250 miles 
(10 000 km) or twice a year, whichever comes 
first and tightened or replaced if necessary. Any 
hose which is chafed, worn or kinked should be 
replaced. 

Teflon-braided stainless steel hoses used in the 
engine compartment must be replaced only with 
similar hoses. 

8.3 NYLON 

TUBING 

Nylon tubing is used for air lines in areas where 
usage of this material is suitable. Nylon tubing is 
flexible, durable, and weather resistant. When 
replacing an air line, use nylon tubing only 
where it has been used previously.  

Nylon air lines must never be routed in areas 
where temperature could exceed 200

o

F (93

o

C). 

CAUTION

 

Nylon air lines should be used to replace 
existing nylon lines only, and must comply 
with the color identification code to ease 
pneumatic system troubleshooting. 

8.4 

AIR LINE OPERATING TEST 

If any trouble symptom such as slow brake 
application or slow brake release indicates a 
restricted or clogged air line, disconnect the 
suspected tube or hose at both ends and blow 
through it to clear the passage. 

Inspect tubing and hose for partial restriction 
that may be caused by dents or kinks. If such a 
condition is found, the tubing or hose should be 
replaced. 

8.5 

AIR LINE LEAKAGE TEST 

With air system fully charged and the brakes 
applied, coat all tubing and hose connections 
with a soapy solution to check for air leakage. 
No leakage is permitted. Leakage can 
sometimes be corrected by tightening the 
connection. If this fails to correct the leakage, 
new fittings, nylon tubing, copper tubing, 
teflon-braided stainless steel and flexible hoses 
must be installed as applicable. 

 

Summary of Contents for LE MIRAGE XLII































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for LE MIRAGE XLII

Brands by name

Popular brands

Load more brands