5-32 OTHER FEATURES
PA1633 X3-45 Commuter Operator’s Manual
12. LOWER HANDRAILS: Press release button
at base of handrail and lift the left handrail
upward out of its socket. Lower handrail to
platform. Repeat for right handrail. Buckle
safety belt.
13. STOW PLATFORM: Press and hold STOW
button. Close wheelchair area door at
intermediate height. Press and hold STOW
button until platform reaches STOW height
and then fully retracts into vehicle.
14. CLOSE DOOR. Close the lift access door.
WARNING
Inspect the lift before each use as described
in the RICON Owner’s manual. If any unsafe
condition exists, or if unusual noises or
movements are noticed, DO NOT use and
contact an authorized RICON dealer for
repair.
WARNING
Read and comply with all warning labels and
symbols affixed to the wheelchair lift.
WARNING
Do not operate with a load in excess of 660
lbs (300 Kg).
NOTE
The restraint belt acts as a safety device and
it prevents raising or lowering the lift when not
buckled.
WARNING
Use extreme care when rolling on or off the
platform and lock the wheelchair brakes while
stationary on the platform. Make sure the
wheelchair fits safely on the platform. Keep
arms and legs away from moving parts.
NOTE
The indicator light on the control device
illuminates when power is supplied (when the
lift electrical circuit is activated by the power
switch on the dashboard).
THRESHOLD WARNING SYSTEM (TWS)
ADJUSTMENT
There are three verifications to perform; 1)
Adjust Aiming of Acoustic Sensor Beam, 2) Test
Aim of Acoustic Sensor Beam, and 3) Adjust
Acoustic Sensor Timing.
Adjustment of the sensor timing is done at the
factory and should not need to be repeated in
the field. Readjustment should only be
considered if the sensor aiming could not be
adjusted to ignore both the wheelchair in the
aisle and the platform during its normal
movement.
Adjust Aiming of Acoustic Sensor Beam
1. Place wheelchair with passenger in center
aisle of coach, pointed at doorway where
Threshold Warning System (TWS) is
installed. The TWS should not detect a
wheelchair and passenger when they are
located this far from doorway.
2. Turn power to lift on (LED on TWS module
will light steady) and indicator light on the
control device illuminates. If wheelchair and
passenger are detected by acoustic sensors
the LED will flash, the buzzer will sound and
the module red light will flash. If this occurs it
is necessary to adjust aiming of sensors.
TWS AREA
23371
Summary of Contents for X3-45 COMMUTER 2018
