background image

25

Storage

Your Go-Chair should be stored in a dry place, free from temperature extremes. When storing, disconnect 
the batteries from the Go-Chair. See “Batteries and Charging.”

WARNING! If you fail to store the unit properly, the frame can rust and the electronics 

can be damaged.

Batteries that are regularly and deeply discharged, infrequently charged, stored in extreme temperatures, 
or stored without a full charge may be permanently damaged, causing unreliable performance and limited 
service life. It is recommended that you charge the batteries periodically throughout periods of prolonged 
storage to ensure proper performance.

You may wish to place several boards under the frame of your Go-Chair to raise it off of the ground during 
periods of prolonged storage. This takes the weight off the tires and reduces the possibility of fl at spots 
developing on the areas of the tires contacting the ground.

Disposal of Your Go-Chair

Your Go-Chair must be disposed of according to applicable local and national statutory regulations. 
Contact your local waste disposal agency or authorized Pride Provider for information on proper disposal 
of travel chair packaging, metal frame components, plastic components, electronics, batteries, neoprene, 
silicone, and polyurethane materials.

Cleaning and Disinfection

 

Use a damp cloth and mild, non-abrasive cleanser to clean the plastic and metal parts of your Go-
Chair. Avoid using products that may scratch the surface of your chair.

 

If necessary, clean your product with an approved disinfectant. Make sure the disinfectant is safe for 
use on your product before application.

WARNING! Follow all safety instructions for the proper use of the disinfectant and/or 

cleaning agent before applying it to your product. Failure to comply may result in skin 

irritation or premature deterioration of upholstery and/or travel chair fi nishes.

WARNING! Never hose off your travel chair or place it in direct contact with water. Your 

travel chair has a painted, ABS plastic body shroud that allows it to be easily wiped 

clean with a damp cloth.

WARNING! Never use any chemicals to clean a vinyl seat, as they may cause the seat 

to become slippery or dry out and crack. Use soapy water and dry the seat thoroughly.

Summary of Contents for Go-Chair

































Reviews: