background image

T

able 1. Go-Go Elite T

raveller Plus Beep Codes

  

 BEEP 

CODE

  

  

  

  

  

FA

UL

T

  

  

  

IMP

A

CT 

ON 

SCOO

TER

                      NO

TES

BEEP 

CODE 

#3

Battery 

voltage 

is 

above 

32VDC.

Drive 

inhibited.

Battery charge is too high. If the charger is plugged

(Ma

Stop 

Slo

wly

.)

in, unplug it. Check battery charger output. Replace if it

exceeds 30VDC.

BEEP CODE #5

Brake 

fault

Drive inhibited.

Ref

er 

to 

BEEP CODE #5 - Br

ak

e F

ault.

BEEP CODE #6

Throttle 

T

ri

p

Drive inhibited.

The 

controller has detected that the throttle pot or throttle

control lever is not in the neutral position when turning the

k

e

y s

witch on or that the throttle pot ma

y be f

aulty

. Ref

er to

BEEP CODE #6 - 

Throttle 

T

rip

BEEP CODE #7

Throttle 

T

ri

p

Drive inhibited.

The 

speed 

pot or its wir

ing is f

aulty

. Chec

k f

or open or shor

t

circuits

. Speed P

o

t ma

y not be correctly set up

. Ref

er to

BEEP CODE #7 - 

Throttle 

T

ri

p

.

BEEP CODE #8

Motor 

Disconnected

Drive inhibited.

The 

motor 

or its wir

ing is f

aulty

. Chec

k f

or open or shor

t

circuits. Refer to BEEP CODE #8 - Motor Disconnected.

BEEP CODE #9

P

ossib

le 

Controller 

T

ri

p

Drive inhibited.

The 

controller has an internal fault. Refer to BEEP CODE #9

- P

ossib

le Controller 

T

rip

.

Summary of Contents for Go-Go Elite traveller




















Reviews: