background image

 

 

 

www.pridemobility.com

 

 

18

 

 

V I I I .   W A R R A N T Y  

 

The warranty period for your hoist is 12 months from the date of delivery. 

This warranty 

will cover

 any 

defects of workmanship or function

The warranty 

does not cover

 any incorrectly installed hoist’s or one with damaged mechanical or electrical 

components due to 

incorrect use or damage

The warranty does not cover consequential loss, unless regional law requires it. 

The warranty is invalidated if the seal on either the actuator or control box is broken. These contain no user 
replaceable components. No alteration should be made to the hoist by anyone other than a qualified person, 
as defined by an authorized Pride Provider. 

In the event of damage or defects in the actuator, the hoist should be returned to your authorized Pride 
Provider for evaluation. 

No wires must be cut as they are fitted with connectors that must be correctly removed before repair. 

In the event of any malfunction of the electrical circuit box or handset which require replacement, they 
should be removed and returned as a set. 

 
Please keep a note of the following: 
 

Serial Number: ________________________ 
 
Date Supplied: ________________________ 
 
Details of the Supplier (Stamp): __________ 
 
Zip Code: ____________________________ 
 
Tel: _________________________________ 
 
 

 
Set up details 
 

 
 

  

  

 

 

 

 

 

 

 

 

 

 

 

 
Scooter/Chair Weight: _____________________ 

 

Signed: ____________________ 

If this changes, please check with your authorized Pride Provider 

Model: 
260lb:……………… 

440lb:……………… 

Summary of Contents for Zeus 260/440lb





















Reviews: