Pride Quantum 610, Owner'S Manual

Quantum 610 Series                                            www.pridemobility.com                                                                   35

V I I .   C A R E   A N D   M A I N T E N A N C E

All wheel bearings are prelubricated and sealed. They require no subsequent lubrication.
The body shroud has been sprayed with a clear sealant coating. You can apply a light coat of car wax to help
it retain its high-gloss appearance. 
Check all electrical connections. Make sure they are tight and are not corroded. Batteries must sit flat within
the battery tray, with the battery terminals facing inward, toward each other. Refer to the battery wiring label
for the correct wiring layout. 

WARNING! Even though the power chair has passed the necessary testing

requirements for ingress of liquids, you should keep electrical connections away

from sources of dampness, including direct exposure to water or bodily fluids and

incontinence. Check electrical components frequently for signs of corrosion and

replace as necessary.

Daily Checks

With the controller turned off, check the joystick. Make sure it is not bent or damaged and that it returns to the
neutral position when you release it. Check the rubber boot around the base of the joystick for damage. Visu-
ally inspect the boot. Do not handle or try to repair it. See your Quantum Rehab Provider if there is a problem.
Visually inspect the controller cable. Make sure that it is not frayed, cut, or has any wires exposed. See your
Quantum Rehab Provider if there is a problem.
Check for flat spots on solid tires. Flat spots could adversely affect stability.
Inspect the seating system, armrests, and front riggings for loose hardware, stress points, or damage. See your
Quantum Rehab Provider if there is a problem.

Weekly Checks

Disconnect and inspect the controller from the power base. Look for corrosion. Contact your Quantum Rehab
Provider if necessary.
Ensure that all parts of the controller system are securely fastened to your power chair. Do not overtighten any
screws.
Check for proper tire inflation. Pneumatic tires should be inflated to the psi/bar/kPa air pressure rating indi-
cated on the tire. If a tire does not hold air, see your Quantum Rehab Provider for replacement of the tube.
Check the brakes. This test should be carried out on a level surface with at least 3 feet (1 meter) of clearance
around your power chair.

To check the brakes:

1. Turn on the controller and turn down the speed level of your power chair.
2. After one second, check the battery condition meter. Make sure that it remains on.
3. Slowly push the joystick forward until you hear the electric brakes click. Immediately release the joystick.

You must be able to hear each electrical brake operating within a few seconds of joystick movement. Repeat
this test three times, pushing the joystick backwards, then left, and then right.

Monthly Checks

Check for drive tire wear. See your Quantum Rehab Provider for repair.
Check the caster wheels for wear. Replace them as necessary.
Check the caster forks for damage or fluttering which indicates that they may need to be adjusted or have the
bearings replaced. See your Quantum Rehab Provider for repair.
Check the entire power chair for loose hardware and changes in the function or performance of the power
chair. See your Quantum Rehab Provider for service and repair.
Keep your power chair clean and free of foreign material, such as mud, dirt, hair, food, drink, etc.

Yearly Checks

Take your power chair to your Quantum Rehab Provider for yearly maintenance, especially if you use your power chair
on a daily basis. This helps ensure that your power chair is functioning properly and helps prevent future complications.

36                                                                  www.pridemobility.com                                     Quantum 610 Series

V I I .   C A R E   A N D   M A I N T E N A N C E

Storage

Your power chair should be stored in a dry place, free from temperature extremes. When storing, disconnect the
batteries from the power chair. See VI. “Batteries and Charging.” 

WARNING! If you fail to store the unit properly, the frame can rust and the electronics can be

damaged.  

Batteries that are regularly and deeply discharged, infrequently charged, stored in extreme temperatures, or stored
without a full charge may be permanently damaged, causing unreliable performance and limited service life. It is
recommended that you charge the batteries periodically throughout periods of prolonged storage to ensure proper
performance.

You may wish to place several boards under the frame of your power chair to raise it off of the ground during
periods of prolonged storage. This takes the weight off the tires and reduces the possibility of flat spots developing
on the areas of the tires contacting the ground.

Disposal of Your Power Chair

Your power chair must be disposed of according to applicable local and national statutory regulations. Contact
your local waste disposal agency or your Quantum Rehab Provider for information on proper disposal of power
chair packaging, metal frame components, plastic components, electronics, batteries, neoprene, silicone, and poly-
urethane materials.

Cleaning and Disinfection

Use a damp cloth and mild, non-abrasive cleanser to clean the plastic and metal parts of your power chair.
Avoid using products that may scratch the surface of your power chair.
If necessary, clean your product with an approved disinfectant. Make sure the disinfectant is safe for use on
your product before application.

WARNING! Follow all safety instructions for the proper use of the disinfectant and/or cleaning

agent before applying it to your product. Failure to comply may result in skin irritation or

premature deterioration of upholstery and/or power chair finishes.
WARNING! Never hose off your power chair or place it in direct contact with water. Your power

chair has a painted, ABS plastic body shroud that allows it to be easily wiped clean with a damp

cloth.  
WARNING! Never use any chemicals to clean a vinyl seat, as they may cause the seat to become

slippery or dry out and crack. Use soapy water and dry the seat thoroughly.

Wheel Replacement

If you have pneumatic tires and you have a flat tire, you can replace the tube. If your chair is equipped with a solid
tire insert, then you must replace the entire wheel assembly. Replacement tires, tubes, and wheel assemblies are
readily available through your Quantum Rehab Provider. 

WARNING! The wheels on your power chair should only be serviced or replaced by a Quantum

Rehab Provider or a qualified technician.
WARNING! Be sure that the power to the controller is turned off and the power chair is not in

freewheel mode before performing this procedure.
WARNING! When changing a tire, remove only the center lug nut and washer, then remove the

wheel. If any further disassembly is required, deflate the tire completely or it may explode.