Follow all local and national electrical codes.
For assistance please call Prima Customer Ser
vice at 562-407-3079
IMPORTANT Please read these instructions prior to installation. Refer to the Prima catalog for proper lamp type and maximum wattage for fixtures.
Prima is not responsible for any fixture or system failure caused by unsupported lamps. Contact Prima customer service for the latest updates on
which lamps we support and proper usage. Prima low voltage transformers must be used with all Prima Lighting product installations. All warranties
are void if Prima transformers are not used. Prima’s catalogs provide general information and suggestions for proper dimmer usage. Please consult
our customer service department with any questions regarding dimmer specifics. Prima is not responsible for any damage caused by improper
dimmer specification and usage. Use only qualified electrician for installation. Adhere to all local and national electrical codes prior to installation.
It is strongly recommended that gloves are used when handling the FIT System track. Oils and dirt from fingers can sometimes permanently
mark the finish. Track should be cleaned with a damp cloth and thoroughly dried before fixture installation.Connectors are available for
extending track length, turning corners or creating intersections in the run. Great care must be taken to ensure the connector is installed
properly.
T
FIT I System three-way 90º power feed 22-79228 connects and feeds power to three lengths of FIT I track. The construction of the connector
allows the three track lengths to be positioned at 90º angles. Insert the connector into open end of a FIT track length. Secure the
powerfeed by tightening the set screws with a flat head screwdriver at the top and bottom of the connector. Insert the transformer’s low voltage
secondary leads into the power entry connectors on the top of the powerfeed. Using the supplied hex wrench, secure the transformer leads by
tightening the set screws for each wire lead. Transformer low voltage leads must be 10 AWG THHN stranded. NOTE: Power is fed to the bottom slot
three-way 90º power feed -
22-79228
four-way 90º power feed -
22-79229
U
FIT I System four-way 90º power feed 22-79229 connects and feeds power to four lengths of FIT I track. The construction of the connector
allows the four track lengths to be positioned at 90º angles. Insert the connector into open end of a FIT I track length. Secure the powerfeed
by tightening the set screws with a flat head screwdriver at the top and bottom of the connector. Insert the transformer’s low voltage secondary
leads into the power entry connectors on the top of the powerfeed. Using the supplied hex wrench, secure the transformer leads by tightening the
set screws for each wire lead. Transformer low voltage leads must be 10 AWG THHN stranded. NOTE: Power is fed to the bottom slot of the track
two-way 90º power feed -
22-79227
S
FIT I System two-way 90º power feed 22-79227 connects and feeds power to two lengths of FIT I track. The construction of the connector
allows the two track lengths to be positioned at a 90º angle. Insert the connector into open end of a FIT I track length. Secure the
power feed by tightening the set screws with a flat head screwdriver at the top and bottom of the connector. Insert the transformer’s low voltage
secondary leads into the power entry connectors on the top of the powerfeed. Using the supplied hex wrench, secure the transformer leads by
tightening the set screws for each wire lead. Transformer low voltage leads must be 10 AWG THHN stranded. NOTE: Power is fed to the bottom slot
Low voltage
leads from
transformer.
10AWG THHN
stranded
Low voltage leads from
transformer. 10AWG
THHN stranded
Wire connectors may be
repositioned if desired.
Wire connectors may be
repositioned if desired.
Low voltage leads from
transformer. 10AWG
THHN stranded
13615 Marquardt Ave. Santa Fe Springs, CA 90670
Ph. 562-407-3079 . Fx. 562-407-3069
www.primalighting.com
REV
.033015
prima fit I system
general installation instructions part 10 of 12
NOTE: ALL POWERFEED WIRES FEED THROUGH OUR MOUNTING DISK #CO-036 OR J-BOX COVER PLATE #30-JBP.
SOLD SEPARATELY. SEE DIAGRAM ON PAGE PART 12 OF 12 FOR REFERENCE.
