Follow all local and national electrical codes.
For assistance please call Prima Customer Ser
vice at 562-407-3079
IMPORTANT Please read these instructions prior to installation. Refer to the Prima catalog for proper lamp type and maximum wattage for fixtures.
Prima is not responsible for any fixture or system failure caused by unsupported lamps. Contact Prima customer service for the latest updates on
which lamps we support and proper usage. Prima low voltage transformers must be used with all Prima Lighting product installations. All warranties
are void if Prima transformers are not used. Prima’s catalogs provide general information and suggestions for proper dimmer usage. Please consult
our customer service department with any questions regarding dimmer specifics. Prima is not responsible for any damage caused by improper
dimmer specification and usage. Use only qualified electrician for installation. Adhere to all local and national electrical codes prior to installation.
It is strongly recommended that gloves are used when handling the FIT System track. Oils and dirt from fingers can sometimes permanently
mark the finish. Track should be cleaned with a damp cloth and thoroughly dried before fixture installation.Connectors are available for
extending track length, turning corners or creating intersections in the run. Great care must be taken to ensure the connector is installed
properly.
double top power feed -
22-79226
two piece power feed -
22-79300
V
FIT I System double top power feed 22-79226 connects and feeds two separate power circuits to two seperate lengths of FIT I track (one
circuit per track length). This is a rigid straight connector. Insert the connector into an open end of a FIT I track length. Secure the
power feed by tightening the set screws with a flat head screwdriver at the top and bottom of the connector. Insert the transformer’s low voltage
secondary leads from each circuit into the power entry connectors on the top of the power feed. Using the supplied hex wrench, secure the
Low voltage leads from
transformer. 10AWG
THHN stranded
Low voltage leads from
transformer. 10AWG
THHN stranded
Circuit 1
90º
clockwise
gap
no
gap
Circuit 2
W
FIT I System two piece power feed 22-79300 is a versatile piece of hardware that allows powerfeed at any point along the FIT I track length
in either horizontal or veritcal orientation. There are two distinct feeds, one for the HOT terminal and one for the NEUTRAL terminal. The
HOT terminal feed makes contact with the internal conductor bar within the track. Before installing the HOT terminal feed, ensure that the top knurled
knob is unscrewed as much as possible so that there is a significant gap beteween the knurled knobs. Insert the feed into the track slot and rotate
90º clockwise to lock. Secure the feed by tightening the top knurled knob until there is no gap between the knobs.
HOT
NEUTRAL
Ensure that the top knurled
knob is unscrewed as much
as possible before
installation. There should be
a gap between the knobs.
Ensure that there is
no gap between
the knurled knobs
before installation.
90º
clockwise
The NEUTRAL terminal feed makes contact with the track’s outer housing which aslo acts as the NEUTRAL terminal of the track circuit. Before
installation, unscrew the BOTTOM knurled knob until there is NO gap between the knobs. Insert the feed into the track slot about 1/2” from the HOT
terminal feed. Rotate the feed 90º clockwise to lock. Tighten the bottom knurled knob to secure the feed. NOTE: Power is fed to one slot of the track
only. Insert the transformer’s low voltage secondary leads into the power entry connectors on the top of the powerfeed. Using the supplied hex
wrench, secure the transformer leads by tightening the set screws for each wire lead. Transformer low voltage leads must be 10 AWG THHN
HOT Terminal feed
NEUTRAL Terminal feed
13615 Marquardt Ave. Santa Fe Springs, CA 90670
Ph. 562-407-3079 . Fx. 562-407-3069
www.primalighting.com
REV
.033015
prima fit I system
general installation instructions part 11 of 12
NOTE: ALL POWERFEED WIRES FEED THROUGH OUR MOUNTING DISK #CO-036 OR J-BOX COVER PLATE #30-JBP.
SOLD SEPARATELY. SEE DIAGRAM ON PAGE PART 12 OF 12 FOR REFERENCE.
