background image

C

IMPORTANT  Please read these instructions prior to installation. Refer to the Prima catalog for proper lamp type and maximum wattage for fixtures. 

Prima is not responsible for any fixture or system failure caused by unsupported lamps. Contact Prima customer service for the latest updates on 

which lamps we support and proper usage. Prima low voltage transformers must be used with all Prima Lighting product installations. All warranties 

are void if Prima transformers are not used. Prima’s catalogs provide general information and suggestions for proper dimmer usage. Please consult 

our customer service department with any questions regarding dimmer specifics. Prima is not responsible for any damage caused by improper 

dimmer specification and usage. Use only qualified electrician for installation. Adhere to all local and national electrical codes prior to installation.

It is strongly recommended that gloves are used when handling the FIT I System track. Oils and dirt from fingers can sometimes permanently

mark the finish. Track should be cleaned with a damp cloth and thoroughly dried before fixture installation.

FIT I System adapter are installed in the track using a twist-and-lock method. The adapter is inserted at the desired location on the track 

length. Pressure is applied on the adapter to compress the internal contact/pressure mechanism. While applying said pressure, the

adapter is rotated 90º clockwise until it stops. To secure the adapter, the knurled locking ring is rotated clockwise by hand until sufficient pressure 

creates a solid and secure mounting. IMPORTANT: Do not attempt to slide the adapter to other locations on the track length after it is installed. The 

adapter must be completely removed from the track slot and reinstalled at the new location. 

Insert the adapter into the 

track slot

Apply pressure and 

rotate 90º clockwise

After rotation, 

adapter rests 

inside track slot.

Rotate knurled 

locking ring 

clockwise to 

secure the adapter. 

There should now 

be a gap between 

the two knobs.

C1

D1

D2

D3

D4

D5

C2

C3

C4

C5

Ensure that there is 

no gap between 

the knurled knobs 

before installation.

Rotate knurled 

locking ring 

clockwise to 

secure the adapter. 

There should now 

be a gap between 

the two knobs.

Ensure that there is 

no gap between 

the knurled knobs 

before installation.

FIT I SYSTEM TRACK REQUIRES SUPPORT POINTS BE INSTALLED EVERY 4’

FIT I SYSTEM TRACK REQUIRES SUPPORT POINTS BE INSTALLED EVERY 4’

D

l mounted 

support. The following steps cover the general task of inserting the support adapter into the track slot. See the individual steps for various 

support method installation instructions. It is strongly recommended that gloves are used when handling the FIT I System track. Oils and dirt 

from fingers can sometimes permanently mark the finish. Track should be cleaned with a damp cloth and thoroughly dried before fixture

installation.

 FIT I System support adapters are installed in the track using a twist-and-lock method. The support adapter is inserted at the desired

location on the track length. The adapter is rotated 90º clockwise until it stops. With a stem suspended support adapter, it will be 

necessary to SLIGHTLY loosen the stem coupler to allow the adapter to rotate and lock into the track slot. To secure the adapter, the knurled 

locking ring is rotated clockwise by hand until sufficient pressure creates a solid and secure mounting. IMPORTANT: Do not attempt to slide the 

adapter to other locations on the track length after it is installed. The adapter must be completely removed from the track slot and reinstalled at the 

new location. 

Insert the support adapter 

into the track slot

Loosen the set screw with 

the supplied hex wrench. 

(for stem only)

Rotate the adapter 90º 

until the track rests on 

the adapter.

Tighten the set screw 

with the hex wrench. 

(for stem only)

fit I system fixture adapter installation

Follow all local and national electrical codes.

For assistance please call Prima Customer Ser

vice at 562-407-3079

fit I system vertical support adapter installation

13615 Marquardt Ave. Santa Fe Springs, CA 90670
Ph. 562-407-3079 . Fx. 562-407-3069
www.primalighting.com

Black top knob is for

locking purposes. 

Hold the bottom knob with
your fingers. Do not use a 
plier or any other tools that
will hurt the adapter and finish. 

REV

.033015

C

D

prima fit I system

general installation instructions part 2 of 12

Summary of Contents for FIT I

















Reviews: