Prima FIT I Installation Instruction Download

Page: 7 / 16

fit I system support for horizontally oriented track

for stem suppport

Follow all local and national electrical codes.

For assistance please call Prima Customer Ser

vice at 562-407-3079

IMPORTANT Please read these instructions prior to installation. Refer to the Prima catalog for proper lamp type and maximum wattage for fixtures.

Prima is not responsible for any fixture or system failure caused by unsupported lamps. Contact Prima customer service for the latest updates on

which lamps we support and proper usage. Prima low voltage transformers must be used with all Prima Lighting product installations. All warranties

are void if Prima transformers are not used. Prima’s catalogs provide general information and suggestions for proper dimmer usage. Please consult

our customer service department with any questions regarding dimmer specifics. Prima is not responsible for any damage caused by improper

dimmer specification and usage. Use only qualified electrician for installation. Adhere to all local and national electrical codes prior to installation.

It is strongly recommended that gloves are used when handling the FIT I System track. Oils and dirt from fingers can sometimes permanently

mark the finish. Track should be cleaned with a damp cloth and thoroughly dried before fixture installation.

Mounting stem assembly

w/ mounting disk and

track bracket

Locking knob

Mounting

screws

Anchors

Be sure that the items indicated below are included in the package. Mount screw anchors in the mounting surface so that they align with

the holes in the mounting disk. Secure the mounting disk to the mounting surface with the included screws. Secure the track with the

locking knob. Insert the knob into the large hole on the side of the track bracket. Rotate the track locking knob 90º clockwise to lock the track.

Insert the track into the

track bracket by resting

the one slot on the grip

teeth. Then twist the track

into position as shown.

90º clockwise

Insert locking knob

Tighten inner knob

(22-66240 ~ 22-66248)

13615 Marquardt Ave. Santa Fe Springs, CA 90670
Ph. 562-407-3079 . Fx. 562-407-3069
www.primalighting.com

REV

.033015

prima fit I system

general installation instructions part 4 of 12

Summary of Contents for FIT I

















Search results

Summary of Contents for FIT I

Reviews:

Related manuals for FIT I

Brands by name

Popular brands

Prima FIT I, Installation Instruction

Search results

Summary of Contents for FIT I

Reviews:

Related manuals for FIT I

Brands by name

Popular brands