fit I system picture hanging kits
picture hanging kit I
picture hanging kit II
.s
ed
oc
la
cir
tc
el
el
an
oit
an
dn
al
ac
ol
ll
a
wo
ll
oF
97
03
-7
04
-2
65
ta
ec
iv
re
Sr
e
mo
ts
uC
a
mir
Pl
la
c
es
ae
lp
ec
na
ts
is
sa
ro
F
H
a
Insert the top portion of the cable assembly into the slot on the track bracket. Place track bracket onto the pre-mounted FIT I System track
by first catching the grip teeth on the bottom of the bracket on the bottom slot of the track length. Rotate the top portion of the bracket
onto the top slot of the track length. This will capture the top portion of the cable assembly. Secure the track bracket to the track with the track
locking knob. Insert the knob into the large hole on the top of the track bracket. Rotate the track locking knob 90º clockwise to lock the track.
Insert the track adapter into the bottom slot of the FIT I System track length. Rotate the track adapter 90º clockwise so that it locks into the
slot. Rotate the upper knurled knob of the track adapter clockwise until the adapter forms a snug fit with the track length. Adjust the length
of the support cable with the hex wrench and set screws on the track adapter.
I
Adjust the length of the support cable by
loosening the set screw on the bottom cable
lock. Move the cable lock to the desired
length and push or pull the cable to create a
loop that is approximately 3/8” in diameter.
Tighten the set screw.
Adjust the length of the support cable by
loosening the set screw track adapter and
pushing the cable up and through the exit
hole on the adapter. When the desired length
is achieved, tighten the set screw.
Once properly installed,
the picture hanger kit may
hold up to a 20lb physical
load. ENSURE THAT ALL
KNOBS AND SET
SCREWS ARE
TIGHTENED.
Once properly installed,
the picture hanger kit may
hold up to a 20lb physical
load. ENSURE THAT ALL
KNOBS AND SET
SCREWS ARE
TIGHTENED.
90º clockwise
90º
clockwise
Tighten lower knob
22-79394 cable
Assembly
22-79395 cable
assembly
H1
I
1
I
5
I
7
I
6
I
2
I
3
I
4
H2
H3
H4
H5
H6
H7
H8
H9
H10
H11
Tighten
upper
knob
Multiple support
units may be used
for added stability.
Multiple support
units may be used
for added stability.
22-79240 track bracket is required. A 22-79240
may be ordered specifically for this picture
hanger or an existing 22-79240 on the track
layout may be used. Example: A wall support
uses the same bracket and may serve double
duty to support both the track and the
22-79394 picture hanger kit.
IMPORTANT Please read these instructions prior to installation. Refer to the Prima catalog for proper lamp type and maximum wattage for fixtures.
Prima is not responsible for any fixture or system failure caused by unsupported lamps. Contact Prima customer service for the latest updates on
which lamps we support and proper usage. Prima low voltage transformers must be used with all Prima Lighting product installations. All warranties
are void if Prima transformers are not used. Prima’s catalogs provide general information and suggestions for proper dimmer usage. Please consult
our customer service department with any questions regarding dimmer specifics. Prima is not responsible for any damage caused by improper
dimmer specification and usage. Use only qualified electrician for installation. Adhere to all local and national electrical codes prior to installation.
It is strongly recommended that gloves are used when handling the FIT I System track. Oils and dirt from fingers can sometimes permanently
mark the finish. Track should be cleaned with a damp cloth and thoroughly dried before fixture installation.
13615 Marquardt Ave. Santa Fe Springs, CA 90670
Ph. 562-407-3079 . Fx. 562-407-3069
www.primalighting.com
REV
.033015
prima fit I system
general installation instructions part 6 of 12
