not to scratch the hood.
Replace the bulbs with new ones of the same type.
• Commands:
(
Fig.22
)
Push-button A
= on/off lights switch
Push-button B
= on/off cooker hood switch. The appliance
switches on at speed level 1, If the cooker hood is on depress
the push-button for 2 sec. to switch off the cooker hood. If
the cooker hood is at speed level 1 it will not be necessary
to depress the push-button to switch the cooker hood off .
Decreases the motor speed.
Display C
= indicates the motor speed level selected and
activates the timer.
Push-button D
= switches on the cooker hood. Increases the
motor speed. Touching the key at 3rd speed, the intensive
function runs for 10’, then the appliance go back to work at the
original speed. During this function the display blinks.
Key E
= The Timer times the functions on activation for 15
minutes, after which they are switched off . The Timer is deac-
tivated by re-pressing
Key E
. When the Timer is activated the
decimal point must fl ash on the display. The Timer cannot be
activated if the intensive speed is functioning.
The
“clean air”
function is activated by pressing key
E
for 2
seconds when the appliance is switched off . This switches the
motor on for 10 minutes every hour at the fi rst speed. During
functioning a rotary movement of the peripheral segments
must be visualised on the display. When this time has passed
the motor switches off and the fi xed letter
“C”
must be visu-
alised on the display until the motor re-starts after 50 minutes
for another 10 minutes and so on. Press any key apart from
the light keys to return to normal functioning. Press key
E
to
deactivate the function.
• Active carbon/grease fi lter saturation:Fig.22
- When display item
C
fl ashes, at a speed where it alternates
with the letter
F
(e.g. 1 and
F
), the
grease
fi lters must be
washed.
- When display item
C
fl ashes, at a speed where it alternates
with the letter
A
(e.g. 1 and
A
), the
carbon
fi lters must be
replaced.
After the clean filter has been positioned correctly, the
electronic memory must be reset by pressing button
A
for
approximately
5 seconds
, until the indication
F
or
A
shown
on the display
C
stops fl ashing.
• Commands: Electronic
(
Fig.23 A
):
A
= LIGHT
B
= OFF/SPEED I
C
= SPEED II
D
= SPEED III
E
= AUTOMATIC STOP TIMER – 15 minutes
(*)
F
= FILTER SATURATION RESET LIGHT
When the “fi lter saturation” light fl ashes, the anti-grease fi lters
must be washed. When the light comes on without fl ashing,
the anti-grease fi lters must be washed and the carbon fi lters
replaced (in case of operation whit the recycling version).
When this operation has been completed, press the key to
reset it.
• Commands:
-
Luminous
(
Fig.24
)
-
Electronicthe
(
Fig. 23B
) key symbols are explained below:
A
= LIGHT
B
= OFF
C
= SPEED I
D
= SPEED II
E
= SPEED III
F
= AUTOMATIC STOP TIMER - 15 minutes
(*)
•
If your appliance does not have the
INTENSIVE
speed
function, press key E for two seconds and it will be activated
for 10 minutes after which it will return to the previously set
speed. When the function is active the LED fl ashes. To interrupt
it before the 10 minutes have expired press key
E
again.
•
By pressing key
F
for two seconds (with the hood switched
off ) the “
clean air
” function is activated. This function switches
the appliance on for ten minutes every hour at the fi rst speed.
As soon as this function is activated the motor starts up at the
fi rst speed for ten minutes, During this time key
F
and key
C
must fl ash at the same time.
After ten minutes the motor switches off and the LED of key
F
remains switched on with a fi xed light until the motor starts
up again at the fi rst speed after fi fty minutes and keys
F
and
C
start to fl ash again for ten minutes and so on.
By pressing any key for the exclusion of the hood light the
hood will return immediately to its normal functioning (e.g.
if key D is pressed the “
clean air
” function is deactivated and
the motor moves to the 2nd speed straight away. By pressing
key
B
the function is deactivated).
(*)
The
“automatic stop timer”
delays stopping of the hood,
which will continue functioning for 15 minutes at the operat-
ing speed set at the time this function is activated.
• Active carbon/grease fi lter saturation: Fig.23B / Fig.24
- When button
A
fl ashes at a frequency of
2 seconds
, the
grease
fi lters must be cleaned.
- When button
A
fl ashes at a frequency of
0.5 seconds
, the
carbon
fi lters must be replaced.
After the clean fi lter has been replaced, the electronic memory
must be reset by pressing button
A
for approximately
5
seconds
, until the light on the button stops fl ashing.
• Commands:
(
Fig.25A
)
Mechanical
(
Fig.25B
)
Elliptic
the key
symbols are explained below:
A
= LIGHT
B
= OFF
C
= SPEED I
D
= SPEED II
E
= SPEED III
G
= MOTOR WORKING indicator
THE MANUFACTURER DECLINES ALL RESPONSIBILITY
FOR EVENTUAL DAMAGES CAUSED BY BREACHING THE
ABOVE WARNINGS.
- 24 -
Summary of Contents for LIA729
