background image

CAUTIOUSLY 

put your weight on the stand’s platform.

The additional weight will create tension on the tree strap and cables.

STEP 3:  

Pull the excess strap to 

secure the stand to the tree, as shown 

in 

Fig. 3

. The stand should be tight to 

the tree as shown in 

Fig. 4.

STEP 6:  

When moving from your 

climbing aid to your Hang-On Tree 

Stand, step down from the aid to 

the stand 

as shown in Fig. 6

Cautiously

 put your weight on the 

stand's platform. The additional 

weight will create tension on the 

tree attachment strap and cables.

DO NOT LIFT THE FOOT PLATFORM WHILE THE STAND IS 

IN USE. LIFTING THE FOOT PLATFORM COULD CAUSE 

YOUR STAND TO SHIFT, RESULTING IN SERIOUS INJURY 

OR DEATH. YOU MUST ALSO WEAR A SAFETY HARNESS 

AT ALL TIMES WHILE THE STAND IS IN USE, INCLUDING 

CLIMBING AND DESCENDING. FAILURE TO DO SO COULD  

RESULT IN SERIOUS INJURY OR DEATH.

STEP 1: 

While wearing your 

safety harness, connect your 

climbing belt to the tree following 

manufacturer’s instructions. 

Climb to the desired height using 

your climbing aid. Once you have 

reached the desired height, hoist 

your treestand into position. 

STEP 2:  

With the treestand in the folded position, 

hook Tree Strap into the tree strap bracket. Wrap 

the strap around the tree once and hook the other 

end into the tree strap bracket. 

(

See Fig.1 and Fig. 2.)

 Ensure that the strap is 

not twisted and is laying flat against the tree.  

This should be done beneath where your climbing 

belt is attached to the tree so that your climbing 

belt is above the treestand.

 

STEP 4:  

Unfold the stand by 

bringing the platform downward 

(See Fig.4)

 Pull seat platform 

downward and adjust seat.

CUSTOMER SERVICE DEPARTMENT  1-866-972-6168

Installation Instructions

FIGURE 2

FIGURE 1

FIGURE 3

FIGURE 4

FIGURE 5

STEP 1

STEP 2

STEP 3

STEP 4

STEP 4:  

View of the tree-stand 

once installed on the tree. 

(See Fig.5)

 

STEP 5

STEP 6

W A R N I N G

FIGURE 6

WWW.PRIMALTREESTANDS.COM

Distributed by Primal Vantage Company Inc., 2407 W. Euclid Ave., Littleton, CO  80120

9

©2019 (rev. 1/19)

Model: PVHO-220

Comfort King Deluxe Steel Hang-On Stand

Summary of Contents for PVHO-220













Reviews: