background image

INSTALLING ON TREE

Step 1:  With PLATFORM folded up,

place UPPER TREE CONTACTS against

tree (fig 1).

Step 2:  Wrap TREE STRAP around tree

and attach each hook into TREE

BRACKET (fig 2).

Step 3:  Pull TREE STRAP tight, making sure TREE

CONTACTS are resting against tree (fig 3).

Note

Note

:    

:    

Practice with your product, wearing  entire hunting gear & Safety Harness at ground level BEFORE ascending to any height. 

FOR  YOUR  SAFETY:

FOR  YOUR  SAFETY:

1.  Once TREE STAND is secured to tree, tie one end of

HOIST ROPE to YOUR GEAR while still on ground.

2.  With HOIST ROPE in hand, climb up to PLATFORM  

and  IMMEDIATELY STRAP YOUR SAFETY HARNESS TO TREE. 

3.  Raise GEAR to PLATFORM using HOIST ROPE. 

FOR  YOUR  SAFETY:

FOR  YOUR  SAFETY:

!

!

Check every ladder section BEFORE you leave the ground.

!

!

Sectional ladders must not be anymore than 18” apart.

!

!

USE A HAUL LINE TO RAISE AND LOWER YOUR STAND.  DO NOT CARRY STAND IN HAND OR ON BACK WHILE CLIMBING

Cautiously

Cautiously

when using a climbing belt to ascend tree, the full body safety harness must be attached to tree BEFORE stepping down on tree stand.

Cautiously

Cautiously

put your weight on the stand platform. The additional weight will create tension on tree strap cables.

Step 5:  When moving from climbing

aid to tree stand, step down or over

from climbing aid to stand (fig 7).

Step 4:  After TREE STRAP has been pulled tight, pull down on FRONT OF PLATFORM until it is parallel with ground. (fig 4, 5, 6).

NOTE

NOTE

:

:

If all TREE CONTACTS are not touching tree, fold PLATFORM back up and loosen STRAP, re-set STAND and repeat process.

Step 1:  Fold PLATFORM upward. This

will de-activate “Caming Action” and

release pressure from strap (fig 1).

Step 2:  While holding STAND, pull

RELEASE LOOP on TREE STRAP.

It will loosen (fig 2).

TAKE DOWN STAND

Step 3:  Unhook TREE STRAP from

TABS and lower STAND to ground using

a rope of appropriate length (fig 3).

fig 2

fig 1

fig 3

fig 4

fig 5

fig 6

fig 7

THE  

CHALLENGER 

HANG-ON

Model #9201C / #51004

Release Loop

3

2

1

Distributed by Primal Vantage Company Inc. 685 Route 10 East, Randolph, NJ 07869

Customer Service Department 1-866-972-6168

www.primalparts.com

©2012 (rev. 11/11)

Summary of Contents for THE CHALLENGER 51004/9201










Reviews: