PrimAster 39012299933, Instruction Manual

26 | GB

Please note that our equipment has not been de-

signed for use in commercial, trade or industrial 

applications. Our warranty will be voided if the equip-

ment is used in commercial, trade or industrial busi-

nesses or for equivalent purposes.

5.  Safety information

General power tool safety warnings 

m

WARNING: Read all safety warnings, instruc-

tions,  illustrations  and  specifications  provided 

with this power tool. 

Failure to follow all instructions 

listed below may result in electric shock, fire and/or 

serious injury.

Save all warnings and instructions for future ref-

erence. 

The term “power tool” in the warnings refers to your 

mains-operated (corded) power tool or battery-oper-

ated (cordless) power tool. 

1) Work area safety

a)  Keep work area clean and well lit. 

Cluttered or 

dark areas invite accidents.

b)  Do not operate power tools in explosive at-

mospheres, such as in the presence of flam

-

mable liquids, gases or dust. 

Power tools cre-

ate sparks which may ignite the dust or fumes.

c)  Keep children and bystanders away while op-

erating a power tool. 

Distractions can cause you 

to lose control.

2) Electrical safety

a)  Power tool plugs must match the outlet. Never 

modify the plug in any way. Do not use any 

adapter plugs with earthed (grounded) power 

tools. 

Unmodified plugs and matching outlets will 

reduce risk of electric shock.

b)  Avoid body contact with earthed or grounded 

surfaces, such as pipes, radiators, ranges 

and refrigerators. 

There is an increased risk of 

electric shock if your body is earthed or grounded.

c)  Do not expose power tools to rain or wet con-

ditions. 

Water entering a power tool will increase 

the risk of electric shock.

d)  Do not abuse the cord. Never use the cord 

for carrying, pulling or unplugging the pow-

er tool. Keep cord away from heat, oil, sharp 

edges or moving parts. 

Damaged or entangled 

cords increase the risk of electric shock.

e)  When operating a power tool outdoors, use an 

extension cord suitable for outdoor use. 

Use 

of a cord suitable for outdoor use reduces the risk 

of electric shock.

3.  Scope of delivery

•  Crosscut, drag and mitre saw

•  1 x Clamping device (7) (preassembled)

•  2 x Workpiece support (8) (preassembled)

•  Sawdust bag (17)

•  Allen key 6 mm (D)

•  Allen key 3 mm (C)

•  Operating manual

•  Machine stand

4.  Intended use

The crosscut, drag and mitre saw is designed to 

crosscut wood and plastic respective of the machine’s 

size. The saw is not designed for cutting firewood.

Warning!

 Do not use the saw to cut materials other 

than those specified described in manual.

Warning!

 The supplied saw blade is only intended 

for the sawing of wood! Do not use this blade for the 

sawing of firewood!

The equipment is to be used only for its prescribed 

purpose. Any other use is deemed to be a case of 

misuse. The user / operator and not the manufacturer 

will be liable for any damage or injuries of any kind 

caused as a result of this.

The equipment is to be operated only with suitable 

saw blades. It is prohibited to use any type of cutting-

off wheel.

To use the equipment properly you must also observe 

the safety information, the assembly instructions and 

the operating instructions to be found in this manual.

All persons who use and service the equipment have 

to be acquainted with this manual and must be in-

formed about the equipment’s potential hazards. It is 

also imperative to observe the accident prevention 

regulations in force in your area. The same applies 

for the general rules of health and safety at work.

The manufacturer will not be liable for any changes 

made to the equipment nor for any damage result-

ing from such changes. Even when the equipment is 

used as prescribed it is still impossible to eliminate 

certain residual risk factors. The following hazards 

may arise in connection with the machine’s construc-

tion and design:

•  Contact with the saw blade in the uncovered saw 

zone.

•  Reaching into the running saw blade (cut injuries).

•  Kick-back of workpieces and parts of workpieces.

•  Saw blade fracturing.

•  Catapulting of faulty carbide tips from the saw blade.

• 

Damage  to  hearing  if  ear-muffs  are  not  used  as 

necessary.

•  Harmful emissions of wood dust when used in 

closed rooms.