TROUBLESHOOTING
T
O PREVENT INJURY
,
ALWAYS
DISCONNECT
THE
AIR
SUPPLY
HOSE
WHEN ADJUSTING
,
SERVICING OR DISASSEMBLING THE TOOL
.
F
IRST
:
C
HECK THE
C
OMPRESSED AIR SUPPLY
Many of problems come from a faulty or inadequate
compressed air supply system. Before attempting to
repair the tool, the following points should be checked:
• Check the pressure at the output of the compressor;
adjust to 80-100 psi (5.5-7.0 bar) as required.
• Check the tank pressure of the compressor & adjust
the start/stop limits.
• Check the air delivery system; a 3/8" hose is
recommended.
• Use fewer tools simultaneously; do not exceed the
capacity of the compressor or of the delivery system.
• Drain water from the compressor.
S
ECOND
:
C
HECK FOR AIR LEAKS
At rest, this tool should not have any air leaks. Before
attempting to repair the tool and replace parts, check the
following:
• Check all seals in head, valve and cylinder
assemblies; replace if necessary.
• Check the top edge of main cylinder for burrs or dents.
• Clean & lubricate the head and valve assemblies;
re-assemble the head assembly carefully.
• Check the interior of the head for scratches.
A more comprehensive list of tips and
hints at
http://ts.primatech.ca/tips
SCHEMATICS
With your tool Serial Number at hand,
go to our support web site to retrieve the
schematic specific to your tool:
http://ts.primatech.ca/550
For more information, contact technical support:
by phone
1 (800) 363-1962
by email
support@primatech.ca
TOOL WARRANTY AND LIMITATIONS
Primatech warrants that newly purchased fastening tools,
parts and accessories will be free from defects in material
and workmanship (excluding wear parts) for the period
shown below, after the date of purchase by the original
user as evidenced by a valid purchase invoice.
ONE-YEAR LIMITED WARRANTY will apply to all parts,
except those subjected to normal wear
SEVEN-YEAR EXTENDED LIMITED WARRANTY
covers tool casing.
WARRANTY STATEMENT
Primatech ‘s sole liability hereunder will be to replace any
part or accessory which proves to be defective within the
specific time period. Any replacement part or accessories
provided in accordance with this warranty will carry a
warranty for the remainder of the period of warranty
applicable to the part it replaces. When repair or
replacement of part or tool is required, the complete tool
or part(s) must be returned to Primatech or at such
authorized warranty service point of Primatech,
transportation prepaid, with a copy of proof of purchase
evidencing that the part or tool is within the warranty
period. Serial # must be intact and legible for warranty to
apply.
This warranty is void as to any tool which has been
subjected to misuse, abuse, accidental or intentional
damage, used with fasteners not meeting Primatech
specifications, size or quality, improperly maintained,
repaired with other than genuine Primatech replacement
parts, damaged in transit or handling, or which, in
Primatech ‘s sole opinion, has been altered, modified or
repaired in a way that affects or detracts from the
performance of the tool.
PRIMATECH MAKES NO WARRANTY, EXPRESSED
OR IMPLIED, RELATING TO MERCHANTABILITY,
FITNESS, OR OTHERWISE, EXCEPT AS STATED
ABOVE, and Primatech‘s liability AS STATED ABOVE
AND AS ASSUMED ABOVE is in lieu of all other
warranties arising out of, or in connection with, the use
and performance of the tool, except to the extent
otherwise provided for by applicable law.
PRIMATECH SHALL IN NO EVENT BE LIABLE FOR
ANY DIRECT, INDIRECT, OR CONSEQUENTIAL
DAMAGES W HICH MAY ARISE FROM LOSS OF
ANTICIPATED PROFITS OR PRODUCTION,
SPOILAGE OF MATERIALS, INCREASED COST OF
OPERATION, OR OTHERWISE. Any liability, if any,
connected with the use of the tool shall terminate upon the
expiration of the warranty period specified above.
