background image

To Activate:

1. While the vehicle engine is running with the ignition key turned on, press

the remote control START button for 1-2 seconds. The parking lights will

flash 2 times and then stay on. (Make sure the vehicle is in "Park" and set

the emergency parking brake.)

2. Turn the ignition key off and the engine will stay running.
3. Remove the ignition key and remote control and exit the vehicle.

Remember to keep the ignition key and remote control in your possession.

4. Press the remote control LOCK button for 1-2 seconds to secure your vehicle.

To Deactivate:

1. When you return to the vehicle, press the remote control UNLOCK button

for 1-2 seconds. The doors will unlock.

2. Enter the vehicle (do not touch the brake pedal), turn the ignition key to the 

"ON" position and then press the brake pedal. The parking lights will shut

off and you will now be able to drive the vehicle.

Protected Valet Mode

You should place your system in Protected Valet Mode whenever your vehicle 

is being serviced by mechanics, car wash personnel or driven by valet parking 

attendants. While in the Protected Valet Mode, all remote starter functions are

bypassed to prevent unauthorized or accidental operation. If a remote start is

attempted, the parking lights will flash 4 times and the vehicle will not start.

Remote controlled door lock/unlock and trunk release will still operate.

To Turn on Protected Valet Mode:

1. Turn the ignition key to the "ON" position or start the engine.
2. Flick the valet switch to the "ON" position.
3. The LED will turn on solid red to indicate the system is in the Protected

Valet Mode.

4. Turn the ignition key to the "OFF" position.

To Turn off Protected Valet Mode:

1. Turn the ignition key to the "ON" position or start the engine.
2. Flick the valet switch to the "OFF" position.
3.  The LED will turn off to indicate the system is no longer in the Protected

Valet Mode.

4. Turn the ignition key to the "OFF" position.

9

PrimeStart 450 Owner’s Manual

Summary of Contents for PrimeStart 450

















Reviews: