background image

Horizontal Infrared Toaster 

IRT-SB-NA-1PS 
IRT-SB-NA-3PS 

IRT-SB-NA-1PS 

IRT-SB-NA-3PS 

Electrical Specifications 

Disconnect Power 

WARNING 

Safe Service Practices 

Serial Number Matrix 

The manufacture date is encoded in the unit’s serial number. The 

service bench installation date (used to determine warranty 

coverage) is considered to be the end of the following month. For 

example: 

Serial Number: LK0000458 

Manufacture Date: November 2015 

Service Bench Installation Date: December 15, 2015

IRT-SB-NA-1PS 20

V, 60 Hz,

 4500 W,

 1 Ph.

 

Important 

Prince Castle reserves the right to change specifications 
and product design without notice. Such revisions do not 
entitle the buyer to corresponding changes, improvements, 
additions, or replacements for previously purchased equip-
ment. 

WARNING 

Indicates information important to the proper operation of 
the unit. Failure to observe may result in damage to the 
equipment and/or severe bodily injury or death. 

CAUTION 

Indicates information important to the operation of the unit. 
Failure to observe may result in damage to the equipment. 

GENERAL 

This appliance is designed for toasting bread products in a commercial 
McDonalds kitchen. The dimensions of the bread products as defined 
by McDonalds. 

CAUTION 

Do not hose down or use a water jet on the unit. Keep the unit 
away from running water. Disconnect power cord before perform-
ing any cleaning or maintenance. 

CAUTION 

Equipment must be elevated from the floor at all times during 
cleaning and operation. 

Failure to turn off the unit before 
servicing could result in severe 
bodily injury or death. Switch the 
On/Off switch to the Off position 
before servicing.

 

Printed in USA 

12

/

3

/2020

353

-

56

7

 Rev. 

B

Summary of Contents for IRT-SB-NA-1PS































Reviews: