background image

Specifications

Length ....................................................................................30.125 in (765mm)

Overall Length ...........................................................................35.75 in (908mm)

Beam ........................................................................................  11.0 in (279mm)

Height .......................................................................................  6.75 in (171mm)

Motor ..........................................................  A3630 1800Kv Water-cooled Brushless

Servo ............................................................. Spektrum S100 Metal Gear Hi-torque

Receiver .........................................................................  Spektrum 2.4GHz Marine

Speed Control ............................................................ 60-amp Waterproof Brushless

Hull Material ..........................................................................Fiberglass Composite

Battery ...... 7.4V 2S 25C Li-Po or 7.2V Sub-C with Deans Connector (2) (not included)

Radio ............................................................................... 2-channel (not included)

www.ProBoatModels.com

®

Owners Manual

Summary of Contents for Stiletto

















Reviews: