Pro-Form 1210 RT User Manual Download

Page: 24 / 36

HOW TO USE THE MAINTENANCE MODE

The console features a maintenance mode that allows

you to calibrate the incline and speed of the treadmill,

restore factory defaults, calibrate the screen, update

the console software, and view technical information.

1. Select the settings mode.

See step 1 on page 22.

2. Select the maintenance mode.

Press the Maintenance

button in the lower right

corner of the screen to

enter the maintenance

mode.

3. Calibrate the incline system of the treadmill.

Press the Calibrate Incline button. The frame will

move upward and downward. This will calibrate the

incline system. Press the Begin button to calibrate

the incline system, or press the Cancel button to

return to the maintenance mode. When the incline

system is calibrated, press the Back button.

IMPORTANT: Keep pets, feet, and other objects

away from the treadmill while the incline sys-

tem is calibrating. In an emergency, pull the

key from the console to stop the calibration.

4. Restore factory defaults.

If necessary, press the Restore Defaults button to

reset the firmware to the original factory firmware.

This will erase all firmware updates that you have

downloaded. Press the Begin button to restore the

default firmware, or press the Cancel button to re-

turn to the maintenance mode.

When the restoration is complete, the words

PLEASE CYCLE POWER will appear in the grey

box. Press the power switch into the off position,

wait for several seconds, and then press the power

switch into the reset position. The start menu will

appear when the console is ready for use.

5. Calibrate the screen.

If the screen is not properly calibrated, it will be dif-

ficult for you to press the buttons on the screen. To

calibrate the screen, press the Calibrate Screen

button and then press the Begin button. Press the

Cancel button to return to the maintenance mode.

Using a pencil eraser or other small object, press

the center of the small target on the screen. Then,

press the next two targets. After several seconds,

the console will return to the start menu.

6. Calibrate the speed of the treadmill.

Calibrate the speed of the treadmill only if in-

structed to do so by an authorized service repre-

sentative.

Note: The Calibrate Speed button may not be en-

abled on your treadmill.

7. Update the console firmware.

For the best results, regularly check for

firmware updates.

Press the Firmware Update button. Press the

Begin button to check for updates, or press the

Cancel button to return to the maintenance mode.

A status bar will appear in the grey box on the

screen. When the update is complete, the words

PLEASE CYCLE POWER will appear in the grey

box. Press the power switch into the off position,

wait for several seconds, and then press the power

switch into the reset position. The start menu will

appear when the console is ready for use.

8. View technical information.

Press the Technical Info button to view the total

number of hours that the treadmill has been used

and the total number of miles that the walking belt

has moved. After you view the information, press

the Finish button.

9. Exit the maintenance mode.

To exit the maintenance mode, press the Back but-

ton repeatedly.

Summary of Contents for 1210 RT





































Search results

Summary of Contents for 1210 RT

Reviews:

Related manuals for 1210 RT

Brands by name

Popular brands

Pro-Form 1210 RT, User Manual

Search results

Summary of Contents for 1210 RT

Reviews:

Related manuals for 1210 RT

Brands by name

Popular brands