background image

15

If a different resistance level and/or target speed is

programmed for the next segment, the resistance

level and/or the target speed will flash in the dis-

play for a few seconds to alert you. The resistance

of the pedals will then change.

As you exercise, you will

be prompted to keep your

pedaling speed near the

target speed for the cur-

rent segment. When an

upward-pointing arrow

appears in the display,

increase your speed. When a downward-pointing

arrow appears in the display, decrease your

speed. When no arrows appear, maintain your cur-

rent speed.

IMPORTANT: The target speed is intended only

to provide motivation. Your actual speed may

be slower than the target speed. Make sure to

exercise at a speed that is comfortable for you.

If the resistance level for the current segment is

too high or too low, you can manually override the

setting by pressing the resistance buttons.

IMPORTANT: When the current segment of the

workout ends, the pedals will automatically

adjust to the resistance level for the next seg-

ment.

The workout will continue in this way until the last

segment ends. To stop the workout at any time,

stop pedaling. A tone will sound, the console will

pause, and the time will begin to flash in the dis-

play. To restart the workout, simply resume

pedaling.

4. Follow your progress with the display.

See step 4 on page 13.

5. Measure your heart rate if desired.

See step 5 on page 14.

6. When you are finished exercising, the console

will turn off automatically.

See step 6 on page 14.

HOW TO PLAY THE FAT BLOCKER GAME

The Fat Blocker game requires quick thinking and fast

reflexes. In addition to the console buttons, you will

use the four-button game controllers on the handlebar

to play the game. Follow the steps below to play the

Fat Blocker game.

1. Begin pedaling or press any button on the

console to turn on the console.

When you turn on the console, the display will

light. The console will then be ready for use.

2. Select the Fat Blocker game.

To select the Fat Blocker game, press the Fat

Blockers button (see the drawing on page 12).

3. Begin pedaling or press a button on either

controller to start the game.

When you start the Fat Blocker game, a game

arena will appear in the center of the display.

A block composed of four or five black squares will

slowly move downward until it reaches the bottom

of the arena. Another block will then move down-

ward. Blocks come in eight different shapes. As

each block falls, you can move it to the left or right

using the left and right buttons on the left con-

troller. In addition, you can rotate the block

counterclockwise or clockwise using the left and

right buttons on the right controller. Once you have

positioned and oriented a block, you can speed its

motion to the bottom of the arena, if desired, by

pressing the down button on either controller.

Summary of Contents for 200 CSX

























Reviews: