background image

9

12

When you are finished exercising, remove the
key.

Step onto the foot rails, press the Stop button, and
adjust the incline of the treadmill to the lowest
level. 

The incline must be at the lowest level

when the treadmill is raised to the storage po-
sition or the treadmill will be damaged.

Next,

remove the key from the console and put the key
in a secure place.  

When you are finished using the treadmill, move
the on/off switch near the power cord to the off po-
sition.

6

THE PERFORMANT LUBE

TM

WALKING BELT

Your treadmill features a walking belt coated with PERFORMANT LUBE

TM

, a high-performance lubricant. 

IMPOR-

TANT: Never apply silicone spray or other substances to the walking belt or the walking platform. Such
substances will deteriorate the walking belt and cause excessive wear.

HOW TO PLUG IN THE POWER CORD 

This product must be earthed. 

If it should malfunction or break

down, earthing provides a path of least resistance for electric cur-
rent to reduce the risk of electric shock. This product is equipped
with a power cord having an equipment-earthing conductor and an
earthing plug. 

Important: If the power cord is damaged, it must

be replaced with a manufacturer-recommended power cord.

See drawing 1. Plug the indicated end of the power cord into the
socket on the treadmill. 

If a ferrite box is included,

lift the tab on

the ferrite box and clamp the ferrite box around the power cord.
Fasten the included plastic tie just behind the ferrite box and cut off
the excess plastic tie. The plastic tie will prevent the ferrite box from
sliding along the power cord. 

See drawing 2. Press the pins on the power cord into the metal clips
in the adapter as shown. Close the adapter cover over the end of the
power cord and tighten the screw in the adapter. 

Important: Make

sure that the adapter cover is secure and the screw has been
tightened before using the power cord.

See drawing 3. Plug the power cord into an appropriate outlet that is
properly installed and earthed in accordance with all local codes and
ordinances. 

Important: The treadmill is not compatible with

GFCI-equipped outlets.

DANGER:

Improper connection of the equipment-earthing conductor can result in an in-

creased risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as
to whether the product is properly earthed. Do not modify the plug provided with the product—if it will
not fit the outlet, have a proper outlet installed by a qualified electrician.

Socket on treadmill

Metal 

Clips

1

2

Ferrite Box

Tab

Plastic Tie

Pins

Screw

Adapter

Outlet

3

Adapter

Cover

OPERATION AND ADJUSTMENT

 

Summary of Contents for 360 P PETL30133













Reviews: