background image

16

Locate the Reed Switch (10) and the Magnet (18) on
the left side of the Pulley (17). Turn the Pulley until the
Magnet is aligned with the Reed Switch. 

Make sure

that the gap between the Magnet and the Reed
Switch is about 3 mm (1/8 in.).

If necessary, loosen

the Screw (26) and move the Reed Switch slightly.
Retighten the Screw. Re-attach the Hood (not shown),
and run the treadmill for a few minutes to check for a
correct speed reading.

PROBLEM: The walking belt slows when walked on

SOLUTION:

a. If an extension cord is needed, use only a 3-conductor, 1mm

2

(14-gauge) cord that is no longer

than 1.5 m (5 ft.).

b. If the walking belt is overtightened, treadmill perfor-

mance may decrease and the walking belt may be-
come damaged. Remove the key and 

UNPLUG THE

POWER CORD

. Using the hex key, turn both rear

roller adjustment bolts counterclockwise, 1/4 of a turn.
When the walking belt is properly tightened, you
should be able to lift each side of the walking belt
8–10cm (3-4 in.) off the walking platform. Be careful to
keep the walking belt centred. Plug in the power cord,
insert the key, and run the treadmill for a few minutes.
Repeat until the walking belt is properly tightened.

c. If the walking belt still slows when walked on, call our Customer Service Department.

PROBLEM: The walking belt is off-centre or slips when walked on

SOLUTION:

a. If the walking belt is off-centre, remove the key and

UNPLUG THE POWER CORD

If the walking belt

has shifted to the left,

use the hex key to turn the left

rear roller bolt clockwise 1/2 of a turn; 

if the walking

belt has shifted to the right,

turn the left rear roller

bolt counterclockwise 1/2 of a turn. Be careful not to
overtighten the walking belt. Plug in the power cord,
insert the key, and run the treadmill for a few minutes.
Repeat until the walking belt is centred. 

b. If the walking belt slips when walked on, first remove

the key and 

UNPLUG THE POWER CORD

. Using

the hex key, turn both rear roller bolts clockwise, 1/4
of a turn. When the walking belt is correctly tightened,
you should be able to lift each side of the walking belt
8–10cm (3–4 in.) off the walking platform. Be careful
to keep the walking belt centred. Plug in the power
cord, insert the key, and walk on the treadmill for a
few minutes. Repeat until the walking belt is properly
tightened.

b

a

Rear Roller Adjustment Bolts

8–10 cm

b

18

10

26

Top

View

3 mm

17

Summary of Contents for 360 P Treadmill
























Reviews: