background image

9

7. The Console (16) can use four AA batteries (not

included); alkaline batteries are recommended.

IMPORTANT: If the Console has been

exposed to cold temperatures, allow it to

warm to room temperature before inserting

batteries. Otherwise, you may damage the

console displays or other electronic compo-

nents.

Remove the battery cover, insert the bat-

teries into the battery compartment, and reat-

tach the battery cover.

Make sure to orient the

batteries as shown by the diagram inside

the battery compartment.

7

16

Batteries

Battery Cover

8. Attach the Pivot Bracket (53) to the Upright (13)

with the Pivot Clamp (54) and the Pivot Handle

(55).

Note: The Pivot Handle (55) functions like a

ratchet. Turn the Pivot Handle clockwise, pull it

away from the Upright (13), turn it counterclock-

wise, push it toward the Upright, and then turn it

clockwise again. Repeat this process until the

Pivot Handle is tight.

While a second person holds the Console (16)

near the Upright (13), insert the console wire

through the Pivot Bracket (53) and connect it to

the Extension Wire (23). Then, insert the

excess wire downward into the Upright.

Tip: Avoid pinching the wires.

Attach the

Console (16) to the Pivot Bracket (53) with four

M6 x 15mm Button Screws (46).

8

Avoid pinching

the wires

23

46

46

13

Console Wire

16

53

54

55

9. Attach the Left and Right Pivot Covers (50, 51)

around the Upright (13) with an M4 x 15mm

Round Head Screw (58) and two M5 x 15mm

Round Head Screws (59).

9

59

51

50

59

58

13

All manuals and user guides at all-guides.com

Summary of Contents for 700 Cardio CrossTrainer





















Reviews: