4
21
c. Error code
ÒE3Ó
may appear in the SPEED display if the speed of the walking belt surges above the selected
speed setting. Remove the key, wait for ten seconds, and then reinsert it. If the error code appears again, call
our toll-free Customer Service Department. Do not operate the treadmill until the problem is corrected.
d. Error code
ÒE4Ó
may appear in the SPEED display if the walking belt is moving at a slow speed, and there is
excessive stress on the motor. Remove the key, wait for ten seconds, and then reinsert it. If you weigh over
200 pounds, it may be helpful to increase the incline of the treadmill. If the error code appears again, call our
toll-free Customer Service Department. Do not operate the treadmill until the problem is corrected.
e. Error code
ÒE5Ó
may appear in the PULSE display if a pulse error occurs. See HOW TO USE THE PULSE
SENSOR on page 8, and PULSE DISPLAY on page 12.
5. SYMPTOM: THE PULSE SENSOR DOES NOT FUNCTION PROPERLY
a. See HOW TO USE THE PULSE SENSOR on page 8, and PULSE DISPLAY on page 12.
6. SYMPTOM: THE WALKING BELT IS OFF-CENTRE WHEN WALKED ON
a. If the walking belt has shifted to the left, first remove the key and
UNPLUG THE POWER CORD
. Using the 3/16Ó end of the allen
wrench, turn the left rear roller adjustment bolt clockwise 1/4 of a
turn. Plug in the power cord, insert the key and run the treadmill
for a few minutes. Repeat until the walking belt is centred.
b. If the walking belt has shifted to the right, first remove the key
and
UNPLUG THE POWER CORD
. Using the 3/16Ó end of the
allen wrench, turn the left rear roller adjustment bolt counter-
clockwise 1/4 of a turn. Plug in the power cord, insert the key
and run the treadmill for a few minutes. Repeat until the walking
belt is centred.
7. SYMPTOM: ONE OF THE UPPER BODY ARMS SQUEAKS DURING USE
a. Correcting this problem requires a small amount of white marine
grease, available at most department stores.
Turn the Resistance Knob (59) counterclockwise until it can be
removed. Remove the Resistance Cone (60) and the Upper
Body Arm (12), along with the 3/8Ó Washers (65), Spring
Washer (62), Thrust Washers (63), and Thrust Bearing (64).
(Note: If the Resistance Sleeve [61] comes out of the
Resistance Bracket [66], press it back in.) Apply a
thin layer
of
white marine grease to the outer surface of the Resistance
Cone (60). Reattach all parts in the order shown at the right.
8. SYMPTOM: THE TREADMILL SITS UNEVENLY ON THE FLOOR
a. Make sure that there are seven base pads attached to the treadmill (see assembly steps 1 and 6 on pages
5 and 6).
b
a
Thank you for selecting the PROFORM
¨
785xt tread-
mill. The 785xt treadmill combines advanced technol-
ogy with innovative design to offer you an excellent
form of cardiovascular exercise, in the convenience
and privacy of your home. And when youÕre not exer-
cising, the unique 785xt can be folded up, requiring
less than half the floor space of other treadmills.
For your benefit, read this manual carefully before
using the treadmill
. If you have additional questions,
please call our Customer Service Department at
0345-
089009
. To help us assist you, please note the product
model number and serial number before calling. The
model number of the treadmill is PETL20860. The ser-
ial number can be found on a decal attached to the
treadmill (see the front cover of this manual for the lo-
cation).
Before reading further, please review the drawing
below and familiarise yourself with the labelled parts.
Handrails
Upper Body Arms
Console
Storage Latch
Pulse Sensor
Key/Clip
Circuit Breaker
On/Off
Switch
Walking Belt
Cushioned Walking
Platform for maximum
exercise comfort
Foot Rails
Incline Leg
FRONT
BACK
RIGHT SIDE
Rear Roller
Adjustment Bolt
BEFORE YOU BEGIN
Water Bottle*
Holder
*Water Bottle is not included
Accessory
Tray
60
61
66
12
65
65
59
62
64
63
