20
5
TROUBLE-SHOOTING
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, please call our Customer Service Department.
1. SYMPTOM: THE POWER DOES NOT TURN ON
a. Make sure that the power cord is plugged into a properly earthed outlet. (See HOW TO PLUG IN THE
POWER CORD on page 9.) If an extension cord is needed, use only a 14-gauge general-purpose three cord
of cable of 5 feet (1,5 meters) or less in length.
b. After the power cord has been plugged in, make sure that the key is fully inserted into the console. Various
indicators on the console should light. (See step 1 page 11.)
c. Check the circuit breaker located on the treadmill near the
power cord. If the switch protrudes as shown, the circuit
breaker has tripped. To reset the circuit breaker, wait for five
minutes and then press the switch back in.
d. Check the on/off switch located at the front of the treadmill
near the power cord. The switch must be in the ÒonÓ position.
2. SYMPTOM: THE POWER TURNS OFF DURING USE
a. Check the circuit breaker located on the treadmill near the power cord (see 1. c. above). If the circuit breaker
has tripped, wait for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in.
c. Remove the key from the console, and reinsert it fully into the console. (See step 1 on page 11.)
d. Check to make sure that the on/off switch is in the ÒonÓ position. (See 1. d. above.)
e. If the treadmill still will not run, please call our Customer Service Department.
3. SYMPTOM: THE WALKING BELT SLOWS WHEN WALKED ON
a. If an extension cord is needed, use only a 14-gauge general-purpose three cord of cable of 5 feet (1,5 me-
ters) or less in length.
b. If the walking belt still slows when walked on, please call our Customer Service Department.
4. SYMPTOM: AN ERROR CODE (ÒE1,Ó ÒE2,Ó ÒE3,Ó ÒE4,Ó OR ÒE5Ó) APPEARS ON THE CONSOLE
a. If error code
ÒE1Ó
appears in the DISTANCE/INCLINE display, a malfunction may have occurred in the in-
cline system. Remove the key, wait for ten seconds, and then reinsert it. If the error code appears again, call
our toll-free Customer Service Department. Do not operate the treadmill until the problem is corrected.
b. Error code
ÒE2Ó
may appear in the SPEED display if the SPEED increase or START/PAUSE button is
pressed and no movement of the walking belt is detected within seven seconds. Remove the key, wait for
ten seconds, and then reinsert it. Make sure that you stand on the foot rails of the treadmill each time you
start the walking belt. If the error code appears again, call our toll-free Customer Service Department. Do not
operate the treadmill until the problem is corrected.
Tripped
Reset
Tripped
c
Reset
OFF
ON
ÒOnÓ
Position
d
ASSEMBLY
Assembly requires two people.
Set the treadmill in a cleared area and remove all packing materials. Do not dis-
pose of the packing materials until assembly is completed.
Assembly requires the included allen wrench ,
your own phillips screwdriver , and two adjustable spanners .
1. Attach six Base Pads (73) to the bottom of the Base (75)
in the indicated locations (see the inset drawing). Note:
One additional Base Pad will be used in assembly step 6,
and one extra Base Pad may be included.
2. Firmly hold the Uprights (11, 58) as shown. Raise the
Uprights until the Base (75) and the front Wheels (74)
are resting on the floor.
3. Loosen the Crossbar Bolts (2) in the ends of the Console
Crossbar (17). Pivot the Console (6) to the angle shown.
Look under the Left and Right Crossbar Brackets (4, 51)
and find the two small holes in each end of the Console
Crossbar (17). Tighten Crossbar Screws (9) into all four
holes.
Rotate the Console (6) upward until it stops. Using the
7/32Ó end of the Allen Wrench (57), tighten the Crossbar
Bolts (2) in the ends of the Console Crossbar (17).
4. Next, the treadmill should be raised to the storage posi-
tion. Hold the treadmill with your hands in the locations
shown at the right.
To decrease the possibility of in-
jury, bend your legs and keep your back straight. As
you raise the treadmill, make sure to lift with your
legs rather than your back.
Raise the treadmill about
halfway to the vertical position.
2
11
58
75
3
57
51
9
9
17
4
2
2
1
73
73
73
75
73
4
74
6
