background image

3

Congratulations for selecting the new PROFORM

¨

970R recumbent cycle. Cycling is one of the most
effective exercises for increasing cardiovascular fit-
ness, building endurance, and toning the entire body.
The PROFORM

¨

970R offers an impressive array of

features to let you enjoy this healthful exercise in the
convenience and privacy of your home. 

For your benefit, read this manual carefully before
you use the PROFORM

¨

970R.

If you have additional

questions, please call our Customer Service

Department toll-free at 1-800-999-3756, Monday
through Friday, 6 a.m. until 6 p.m. Mountain Time
(excluding holidays). To help us assist you, please
note the product model number and serial number
before calling. The model number is PFEX38491. The
serial number can be found on a decal attached to the
recumbent cycle (see the front cover of this manual).

Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.

Pulse Sensor

Handlebar

Resistance Knob

REAR

FRONT

Seat 

Backrest

Seat Knob

Wheel

Pedal

Pedal Strap

Console

Book Holder

RIGHT SIDE

BEFORE YOU BEGIN

Summary of Contents for 970R

















Reviews: