background image

4

90 DAYS LIMITED WARRANTY

For a period of ninety (90) days from date of purchase, 

SFA Companies, Inc. 

will repair or replace, at its option, without charge, any of its products 

which fails due to a defect in material or workmanship, or which fails to conform to any implied warranty not excluded hereby.

Performance of any obligation under this warranty may be obtained by returning the warranted product, freight prepaid, to 

SFA Companines, Inc. 

Warranty Service Department, 10939 N. Pomona Ave., Kansas City, MO 64153.

 

Except where such limitations and exclusions are specifically prohibited by applicable law,  (1) the CONSUMER’S SOLE AND EXCLUSIVE 

REMEDY SHALL BE THE REPAIR OR REPLACEMENT OF DEFECTIVE PRODUCTS AS DESCRIBED ABOVE, and (2)

 SFA Companies, Inc.

 

SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGE OR LOSS WHATSOEVER, and (3) THE DURATION OF ANY 

AND ALL EXPRESSED AND IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION, ANY WARRANTIES OF MERCHANTABILITY AND 

FITNESS FOR A PARTICULAR PURPOSE, IS LIMITED TO A PERIOD OF NINETY (90) DAYS FROM DATE OF PURCHASE.

Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.  Some states do not 

allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.  This warranty 

gives you specific legal rights, and you may also have other rights which vary from state to state.

E. REPLACING THE FUSE

(13A 6mm dia. x 30mm glass tube current fuse)

1. Unscrew the plastic 12V DC plug cap.

2. Gently remove 12V fuse and replace with fuse of same 

rating and size.

3. Place fuse properly in position to allow installation of 

plastic cap.

4. Reinstall plastic 12V DC plug cap.

 

TIPS FOR OPERATION

1. Ensure vehicle battery is sufficiently charged to operate 

compressor.

2. If compressor does not operate when plugged into a DC 

12V outlet, check connections at back of DC 12V plug 

as well the receptacle fuse.  Replace as needed with 

a fuse of identical rating.  Never replace with fuse of 

higher rating.  No user replaceable parts exist for this 

item,  refer any repairs to qualified personnel only.

3. Do not overheat the compressor, monitor cycle times 

(compressor’s on and off periods).  Never exceed 15 

minutes continuous running.  Let unit cool for 30 min-

utes, then reattempt use.

4. Operate and store in a clean, dry environment.  Do not 

obstruct the unit’s cooling vents.

Performance Tip:

  Keep your tires inflated per the vehicle’s 

owner’s manual.  This will increase gas mileage and re-

duce tire wear.

SPECIFICATIONS

Model:    

 

W-1806

Power Requirement:    12V DC Neg. Gmd

Maximum PSI:    

130 psi

Duty Cycle:     

15 min. on/30 min. off

Power:   

 

120W @ 12V DC

Maximum Air Flow:   

0.88 CFM

Air Hose Length: 

19.68”

Power Cord Length: 

16.4 ft.

SFA Companies, Inc.

10939 N. Pomona Ave.

Kansas City, MO 64153

Phone (816)891-6390, Fax 

(816)891-6599

Summary of Contents for W-1806

Page 1: ...na Ave Kansas City MO 64153 Tel 816 891 6390 Fax 816 891 6599 Printed in China W 1806 M0_072015 This is the safety alert symbol It is used to alert you to potential personal injury hazards Obey all safety messages that follow this symbol to avoid possible injury or property damage Model W 1806 ...

Page 2: ...ay ignite flammable gases Do not operate in a flammable environment Keep out of reach of children The power cord on this product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm Wash hands after handling California law requires this warning to be given to customers in the State of California Do not alter this product Failure to heed t...

Page 3: ...e air mattresses beach balls life jackets etc remove low pressure inflator and low pressure inflator adapters from storage compartment 2 Connect low pressure inflator adapter onto low pressure deflator outlet in front of low pressure inflator labeled DEFLATION POINT 3 Insert the adapter into the appropriate receiver on the item to be deflated 4 Insert power cord plug in into the detached low press...

Page 4: ... apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state E REPLACING THE FUSE 13A 6mm dia x 30mm glass tube current fuse 1 Unscrew the plastic 12V DC plug cap 2 Gently remove 12V fuse and replace with fuse of same rating and size 3 Place fuse properly in position to allow installation of plastic cap 4 Reinstall plastic 12V DC plu...

Reviews: