background image

2

 

 

 

These symbols are intended to alert the user to the presence of 

important operating and maintenance instructions in the manual 

accompanying the appliance.

RETAIN THIS MANUAL FOR FUTURE REFERENCE

NOTICE

Using  any  part  other  than  genuine  Star  factory  supplied  parts  relieves  the 

manufacturer of all liability.
Star  reserves  the  right  to  change  specifi cations  and  product  design  without 

notice.    Such  revisions  do  not  entitle  the  buyer  to  corresponding  changes, 

improvements,  additions  or  replacements  for  previously  purchased 

equipment.
Due  to  periodic  changes  in  designs,  methods,  procedures,  policies  and 

regulations, the specifi cations contained in this sheet are subject  to change 

without notice.  While Star Manufacturing exercises good faith efforts to provide 

information  that  is  accurate,  we  are  not  responsible  for  errors  or  omissions 

in  information  provided  or  conclusions  reached  as  a  result  of  using  the 

specifi cations.  By using the information provided, the user assumes all risks in 

connection with such use.

MAINTENANCE AND REPAIRS

Contact your local dealer for service or required maintenance.  Please record the model number, serial 

number, voltage and purchase date in the area below and have it ready when you call to ensure a faster 

service. 

 

SAFETY SYMBOL

Model No.

Serial No.

Voltage

Purchase Date

FOR SERVICE CONTACT:

Servequip

Telephone:

 

0-44-08686-8855

Summary of Contents for GR10T4K-CE













Reviews: