background image

18  

PAK152c

E

N

G

L

IS

H

!

TROUBLESHOOTING

PROBLEM

CAUSE

SOLUTION

Will not start

Fuse blown or circuit breaker tripped

Check for cause and replace or reset

Loose electrical connections

Check wiring connections

Extension cord not correct

Max. 50 ft. (15m) minimum 14 gauge.

Overheated motor

Use reset button / wait for automatic reset

Low pressure

Air leak in safety valve

Check valve manually: pull upward on the ring. If 

condition persists, replace valve

Restricted air filter

Clean or replace air filter

Defective check valve

Replace check valve

Safety valve 

releasing

Defective pressure switch or poor 

adjustment

Check for proper adjustment, and if problem persists, 

replace pressure switch.

Oil discharge in air Improper oil viscosity

Replace with SAE20 or SAE30 non-detergent oil

Too much oil in crankcase

Drain crankcase and fill to proper level

Compressor overheated

Air pressure regulated too high

Restricted air filter

Clean or replace air filter

Please contact our Customer help line for replacement parts or specifications.

WARNING!

 Repairs should be made by an authorized repair centre. Opening 

this tool could invalidate your warranty.

wARRANTY

Thank you for investing in a PRO-PULSE power tool. These products have been 

made to demanding, high-quality standards and are guaranteed for domestic use 

against manufacturing faults for a period of 12 months from the date of purchase.

This guarantee does not affect your statutory rights. In case of any malfunction of 

your tool (failure, missing part, etc.), please contact one of our service technician 

at our toll free service line at 

1-866-599-5916 Ext 2

 from 8 AM to 6 PM, Monday 

to Friday, Eastern time. RONA reserves the right to repair or replace the defective 

tool, at its discretion. 

Normal wear and tear, including accessory wear, is not covered under guarantee. 

The product is guaranteed for 12 months if used for normal trade purposes. Any 

guarantee is invalid if the product has been overloaded or subject to neglect, 

improper use or an attempted repair other than by an authorized agent. Heavy-

duty, daily professional or hire usage are not guaranteed. Due to continuous 

product improvement, we reserve the right to change the product specification 

without prior notice.

Summary of Contents for PAK152c



















Reviews: