Probox user manual
Page
39
of
63
PAGE 2/6: You can select three parameters:
Metermode
Fadercal
useFcalib
DAW/prob [0]
Start [0]
No [0]
full DAW [1]
-30dB [1]
Yes [1]
No meter [2]
-10dB [2]
fast prbx [3]
U [3]
Fast DAW [4]
Metermode:
If you select “full DAW“ the DAW sets and clears the Meters of the d8b. If you select
“DAW/prob”, then the meter is set by the DAW and cleared by the probox (no meter artifacts if meter
commands are not send correctly by DAW). The settings fast prbx and fast DAW do the same, but the Leds
react faster. This setting is not possible in normal Mode, only in boost.
I’ve observed that for Cubase the Full
DAW mode seems to be better and for logic the DAW/prob is more usefull.
If you want to use the audio part via the d8b, the dsp board may send meterbridge commands that influence
your visual meterbridge. Therfore it is possible to switch that off.
Fadercal:
here you can calibrate your faders. Press the button above the third vpot
“SELECT”
to start the
calibration. The faders will go near the -30dB position, now move the faders manually to the -30dB. Then press
the button again. The faders will go near -10dB. Proceed as you did with the -30dB on the -10dB position and
also for the U position. Fader Calibration values will be stored when you leave the config setup.
NOTE:
The fadercalibration will scale the fader areas to the dB marks (for Logic). If you want to use the faders
without matching scaling, then set the “useFcalib” to “no” otherwise set it to “yes” if you want to use the
calibration.
PAGE 3/6: You can select three parameters:
Emulation
COM-Speed
Faderfilter
MCU2XT_1 [0]
Boost [0]
0 [0]
MCU2XT_2 [1]
Normal [1]
1-5 [1-5]
3XT [2]
MCU2XT_1
emulates one MCU and 2 XT with a dedicated serialnumber.
MCU2XT_2
emulates one MCU and 2 XT with a different dedicated serialnumber than MCU2XT_1. This is used
if you want to use two d8bs with two proboxes in parallel.
3XT emulates 3 XT. This is used if you want to use two d8bs with two proboxes in parallel, but your DAW
software doesn’t support 2 MCUs at the same time.
NOTE: I cannot guarantee that this will work, as it depends on the DAW software how many MCUs XTs are
supported at the same time.
COM-Speed:
If you are an unlucky guy, your d8b console might be weak to run with the doubled baudrate. In
Summary of Contents for d8b
