background image

4

 

© 2012 by Proceq SA

Safety and Liability

1.1 

General Information

This manual contains important information on the safety, use and maintenance of the Canin

+

. Read 

through the manual carefully before the first use of the instrument. Keep the manual in a safe place 
for future reference.

1.2 Liability

Our “General Terms and Conditions of Sales and Delivery” apply in all cases. Warranty and liability 
claims arising from personal injury and damage to property cannot be upheld if they are due to one 
or more of the following causes: 

• 

Failure to use the instrument in accordance with its designated use as described in this manual.

• 

Incorrect performance check for operation and maintenance of the instrument and its compo-
nents.

• 

Failure to adhere to the sections of the manual dealing with the performance check, operation 
and maintenance of the instrument and its components.

• 

Unauthorised modifications to the instrument and its components. 

• 

Serious damage resulting from the effects of foreign bodies, accidents, vandalism and force 
majeure

All information contained in this documentation is presented in good faith and believed to be correct. 
Proceq SA makes no warranties and excludes all liability as to the completeness and/or accuracy 
of the information. 

1.3 

Safety Instructions

The equipment is not allowed to be operated by children or anyone under the influence of alcohol, 
drugs or pharmaceutical preparations. Anyone who is not familiar with this manual must be super-
vised when using the equipment.

• 

Carry out the stipulated maintenance properly and at the correct time. 

• 

Following completion of the maintenance tasks, perform a functional check.

• 

Pay attention to the correct use and disposal of the copper sulphate solution and the cleaning 
material.

1.4 

Symbols used in the operating instructions

Danger!: 

This symbol indicates a risk of serious or fatal injury in the event that cer-

tain rules of behaviour are disregarded

i

Note: 

This symbol indicates important information

1.5 

Correct Usage

• 

The instrument is only to be used to determine the corrosion potential of rebars in concrete or the 
electrical resistance of concrete. 

• 

Replace faulty components only with original replacement parts from Proceq.

• 

Accessories should only be installed or connected to the instrument if they are expressly autho-
rized by Proceq. If other accessories are installed or connected to the instrument then Proceq will 
accept no liability and the product guarantee is forfeit.

Summary of Contents for canin+





































Reviews: