background image

Version 1.1

 

 

 

  Setup System OFF Time

 

Press 

  or the Menu Button to move or go back to 

the previous menu options. 

Press the ² /¼  buttons to highlight Off Time, and press 

the OK button to select it. 

 
Press the 

  buttons to highlight Off, and press the 

 

buttons to turn this feature on or off. 

 
Press the ² /¼  buttons to highlight the time, and press 

  buttons to adjust the minutes and hours. Set the time 

you would like the display to automatically power off. Exit 
to save these settings. 

 

 

 

 

  Setup System ON Time 

Press 

  or the Menu Button to move or go back to 

the previous menu options. 

Press the ² /¼  buttons to highlight On Time, and press 
the OK button to adjust the settings. 
 
Press the 

 

buttons to highlight the time, and press 

 

buttons to adjust the minutes and hours. Set the time you 
would like the display to automatically power off. 
 
Use the ² /¼  buttons to highlight VOL and use the 

 

buttons to set the volume level you would like the display 
to automatically turn on at. The other options allow you 
to choose how often you want the display to 
automatically turn on (once/daily). Finally, you can 
choose to have this feature ON or OFF. Exit to save your 
settings. 

 

 

  Setup Auto Sleep

 

If Auto Sleep mode is ON, the screen will go to sleep 
when no input signal is received and 5 minutes have 
passed. 

Press 

  or the Menu Button to move or go back to 

the previous menu options. 

 
Press the ² /¼  buttons to highlight Auto Sleep, and 
press the OK button to change the settings. 
 
Press the 

 

buttons to select OFF or ON, and press 

the OK button to select it. 

 

After finish your adjustments, press the [Exit] Button to exit out of the OSD MENU. 

 

 

 

  16

 

Summary of Contents for Touch Table 470


























Reviews: