background image

Jetzt Angebot anfordern auf www.poolseller.de

»

 NOTICE DE MONTAGE

 / OCTO & OCTO +

73

 

Wood is a living material that responds to changes in temperature and humidity; cracks and splits may appear; this is 

natural and in no way impacts the service life of our products.

 

The wooden components of this pool are subjected to an autoclave treatment that complies with standards in effect, they 

present no danger to people or animals that may come into direct contact with the wood. 

 

To preserve the original colour, use a colourless wood finish. You could alternatively opt for a coloured finish or treat 

the wood with a colourless oil to slow the decoloration process.  Before applying the finish, check that it is microporous 

and will allow the wood to breathe. Make sure that the product will not migrate (wet wood) over time to the interior of 

the structure and damage the liner. Ideally, the finish should be applied before assembling the pool structure. Use high 

quality products!!! This will guarantee that the finish will last longer. However, we strongly recommend that you test the product 

on a small unseen part of the pool before applying it to the entire surface area.  

      Over time, the wood will inevitably get dirty. Clean it once a year with a high pressure jet to remove dirt trapped in the 

pores of the wood. Take care to regulate the water pressure to avoid damaging the finish or raising wood fibres. 

 

       This pool is delivered as a kit and is not designed to be dismantled.

 

This pool is designed to be used by persons 3 years of age and older.  It is understood that young children and non-swimmers 

using the pool will wear floatation devices. For your safety and that of your children, we recommend that you read and apply 

the safety recommendations on page 35.

      Use of a pool kit implies adherence to safety recommendations outlined in the maintenance and operating 

instructions.  

 

Octo 440 models, maximum 4 people allowed in the pool at any one time. 

 

Octo 530 models, maximum 5 people allowed in the pool at any one time. 

 

Octo+ 540 and 640x400 models, maximum 6 people allowed in the pool at any one time.

 

Octo+ 840x490, maximum 8 people allowed in the pool at any one time.

      

Ladders should only be used to enter and exit the pool. Any other use is prohibited and could be dangerous.  

     The wooden access ladder should be taken away and stored systematically after the last person leaves the pool. This is to prevent 

the risk of drowning.  We have designed a fast efficient locking system, use it!! Store the ladder in a dry place during the winter. There 

should be no means of access to the pool while it is not in use. The ladder wood should be treated in the same way as the other 

wooden elements. 
      

We recommend that you secure access to the finished pool with one of the measures set out in the French pool 

safety standard NF P 90-306, 307, 308 & 309 that is: Safety barrier -  Alarm  - Safety cover - Shelter.

 

Inspect the accessible nuts and bolts regularly and carry out any maintenance required  (re-tighten, treat traces of rust, etc.).

 

 

Take care with the liner of your pool, do not treat it roughly. Make sure that correct tension is maintained on the liner, failure to 

do so could result in tears and leaks. See the guarantee conditions at the end of these instructions. 

 

During the life of your pool it may be necessary to empty it totally. In this event, take every precaution necessary to avoid 

accidents and danger (falls, etc. ). Avoid leaving the pool empty for more than 48 hours, this could result in deformation of 

the structure. 

     REMINDER:  

No diving  -  No walking on the coping  -  Never leave an empty pool uncovered 

 

      

WATER TREATMENT & MAINTENANCE OF THE FILTRATION SYSTEM

 
       

  To ensure the comfort of pool users, you will need to treat the pool water.  Follow the recommendations concerning 

operation of the filtration group: commissioning, frequency of use for regeneration of the water, maintenance, 

inspections (pipes, nuts and bolts), etc. Monitor the build up of dirt in the sand filter (see the section on filter back 

washing).

 

       Check regularly that the various openings are not obstructed.

       Filtration should be shut down during maintenance on the filtration system.

       In the event of damage to the filtration system, take steps to prevent access to the pool.

       Replace damaged components as quickly as possible. Use only parts approved by our after sales service.

 

      During the pool season, the filter should be run every day for long enough to renew the entire pool water volume at 

least three times every 24 hours.

       To ensure optimal efficiency of the filtration system, make sure that the water level remains correct and constant. 

The water level should be 2/3 of the way up the skimmer mouth. 

       To fill your pool, use tap water, its pH is close to the ideal pH. If you use water from a well or some other private 

source you must have it analysed beforehand.  

You will need to test the pH of your pool at regular intervals and adjust it if necessary to keep it between 7.2 and 7.6. 
Treatment chemicals for this purpose are widely available.

 

 

>>                 

MAINTENANCE AND OPERATION

»

 INSTALLATION INSTRUCTIONS

  / OCTO & OCTO +

Jetzt Angebot anfordern auf www.poolseller.de

Summary of Contents for Piscines Bois ODYSSEA 640 BF Ht 146









































Reviews: