PC-DR3093_IM
19.01.21
39
WARNING: Risk of injury!
1. Remove the mains plug from the socket.
2.
If the appliance is still warm, wait approx. 5 minutes
until removing the lid.
3. Open the lock on the water tank.
4.
Either use the measuring jug included in the delivery or
remove the water tank in order to fill it. Pour water in until
it reaches the
MAX
mark.
5. Close the water tank again with the lock.
6.
If you have removed the water tank first, then place it
back in the appliance. Push it downwards until it snaps
into place.
Electric Connection
1. Before inserting the power plug into the outlet, check
that the mains voltage to be used matches that of the
appliance. You can find the required information on the
nameplate.
2. Connect the appliance to a properly installed earthed
socket.
Using the Appliance
CAUTION:
•
Do a test-cleaning on a non-visible portion first!
• Do not operate the appliance without the cleaning
cloth attached, in order to avoid scratching the floor
covering.
NOTE:
We recommend vacuuming before using the appliance.
1.
To clean carpets, place the appliance on the sole of the
carpet glider (Fig. C).
2. Unwind the entire power cord from the cord wrap.
3.
Turn the steam quantity regulator clockwise until it stops
at the maximum setting.
NOTE:
If the steam quantity regulator is not set to the maxi
-
mum setting the first time it is used, then there is not
enough steam.
4. Press the switch
to turn on the appliance. The power
indicator light will come on.
5.
The appliance will be ready to operate after approxi
-
mately 30 seconds. The pump will start working.
6.
Use the steam quantity regulator to adjust the desired
steam quantity.
7. Move the appliance slowly over the surfaces to be
cleaned. To clean thoroughly, the appliance should be
used on a particular spot for at least 8 seconds, but not
for longer than 15 seconds.
CAUTION:
Make sure there is still enough water left in the tank. Refill
the tank with fresh water in good time (see “Filling the
Water Tank during Operation”).
Filling the Water Tank during Operation
No steam will be discharged if the water tank is empty. The
pump will continue to operate and the heating element will
cause the thermostat to switch on and off periodically.
The water has to be filled up as follows:
1. Press the switch .
2.
Remove the mains plug from the socket!
3.
Fill water up to the maximum mark.
4. Connect the plug to the socket again and switch the
appliance on to continue operation.
End of Operation
1. Press the switch .
2.
Remove the mains plug from the socket!
3. Let the appliance cool down completely.
4. Remove the cleaning cloth from the appliance base.
5.
Empty the water tank.
Cleaning
WARNING:
•
Always pull the plug before cleaning and maintenance.
• Wait until the appliance has cooled down.
• Under no circumstances should you immerse the appliance in
water for cleaning purposes. Otherwise this might result in an
electric shock or fire.
Summary of Contents for 330930
